537059
5
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
Problem Possible Cause Solution
False alarms
Alarm will not sound
Alarm indicator light is flashing red
(monitor is barely detecting
movement)
Power ON indicator does not light up
TROUBLESHOOTING
Baby was removed from crib and Monitor was not
switched OFF .
Sensor Pad cord not connected properly to Monitor.
Sensor Pad is not in full contact with crib mattress, or crib
mattress is not resting on a completely flat or rigid surface.
Baby has moved away from Sensor Pad, to the edge of the crib.
• Monitor is detecting movement when crib is being touched.
Monitor is detecting movement from outside the crib such as
motorized devices, strong drafts, etc.
• Sensitivity is set too high.
Sensor Pad is not in full contact with crib mattress, or crib
mattress is not resting on a completely flat or rigid surface.
Baby is in a very deep sleep or has moved away from Sensor
Pad, to the edge of the crib.
• Batteries are low or improperly installed.
• The Monitor is not ON.
• Turn Monitor to the OFF position.
• Verify the connection between the Sensor Pad and Monitor.
Unplug and reconnect the cord.
• Make sure there is no bedding between mattress and Sensor
Pad. Sensor Pad must rest on a completely flat and rigid surface.
If your crib has a flexible or uneven base (metal spring base,
etc.), place a piece of 6 mm (1/4") plywood to cover the full size
of the crib base.
• Make sure Sensor Pad is positioned as described in the 4
Easy Steps section. Sensitivity may need to be adjusted,
consult the Movement Sensitivity Adjustment section.
Avoid contact with the crib when monitor is ON.
Place crib near a solid supporting wall to avoid Sensor Pad
from detecting movement from outside crib.
You may need to decrease the sensitivity, consult the
Movement Sensitivity Adjustment section.
Make sure there is no bedding between mattress and Sensor
Pad.Sensor Pad must rest on a completely flat and rigid surface:
place a piece of 6 mm (1/4”) plywood to cover the full size of the
crib base.
Make sure Sensor Pad is positioned as described in the 4
Easy Steps section. Sensitivity may need to be adjusted,
consult the Movement Sensitivity
Adjustment section.
Check / replace ba
tteries.
• Check connections or change to another electrical outlet.
• Make sure Monitor is ON.
Testing Your Angelcare
®
Monitor
NOTE: Test your Angelcare
®
Monitor BEFORE first-time use and
then on a periodic basis.
The Angelcare
®
Monitor can be used outside of the crib, in a different
sleeping area. Test monitor when moving Sensor Pad to a new location
to ensure sensitivity is adjusted correctly to the new padding or
mattress. Consult the Movement Sensitivity Adjustment section.
Step 1 Switch the power and “Tic” function to the ON positions. Gently
place your hand on the mattress. The green light will continue to flash
with your every movement. Remove hand from mattress. Due to no
movement, a “pre-alarm Tic” sound will emit after 15 seconds. 5
seconds later, the alarm will sound and the red light will flash
continuously.
NOTE: If alarm does not sound, the Sensor Pad may be detecting a
continuous vibration from the floor, a strong draft or the crib is being
touched. Avoid contact with crib when monitor is in use. Place crib near
a solid supporting wall and away from strong air currents. The
sensitivity of the Sensor Pad may need to be reduced, consult the
Movement Sensitivity Adjustment section.
Step 2 To stop alarm, place your hand lightly on mattress for Sensor
Pad to redetect movement.The red Alarm indicator light on the Monitor
will continue to flash 1 minute (Figure 3).
Step 3 When Monitor produces a rapid “clicking” sound, replace
batteries promptly.
Movement Sensitivity Adjustment
The Sensitivity Adjustment Dial has been preset
to suit most situations. However in certain
circumstances, the sensitivity may not be ideal. DO
NOT increase sensitivity unless false alarms occurs
and you have followed the advice in the
Troubleshooting section for false alarms. Make a note
of the pre-set position of the dial should you wish to
return to it.
The Alarm Indicator Light on the Monitor will flash red when Monitor
barely detects movement. This could be a result of: baby being in a very
deep sleep or baby having moved away from Sensor Pad to edge of crib.
If alarm does NOT sound, no adjustment of sensitivity is required. If the
Alarm Indicator Light flashes red most of the time with baby directly over
the location of either Sensor Pad, a false alarm may occur. If this
happens, adjust the sensitivity.
To adjust sensitivity, increase dial to the next setting. Retest monitor.
5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Angelcare AC300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Angelcare AC300 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Angelcare AC300

Angelcare AC300 Gebruiksaanwijzing - Nederlands - 60 pagina's

Angelcare AC300 Gebruiksaanwijzing - Nederlands - 16 pagina's

Angelcare AC300 Gebruiksaanwijzing - Nederlands - 5 pagina's

Angelcare AC300 Gebruiksaanwijzing - Deutsch, English - 60 pagina's

Angelcare AC300 Gebruiksaanwijzing - English - 10 pagina's

Angelcare AC300 Gebruiksaanwijzing - Français - 60 pagina's

Angelcare AC300 Gebruiksaanwijzing - Français - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info