168467
23
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
To find out more, visit www.alpinetechcenter.com
Copyright 2002 © Alpine Electronics of America, Inc.
Kukje Printing Co., Ltd 127-2 Gamjeon-dong
Sasang-gu Busan Korea
Rev. A-101502
Printing in Korea (S)
68P02294K79-O
STEP 6. (6) TIME CORR. (Time Correction)
Due to the wide variety of installation and system design possibilities available, bass performance may not always
be optimized as a result of speaker placement relative to the listening position. Sound waves may not reach the
listener's ear at the same time as other speakers, especially in a multiple subwoofer configuration. Such differences
in phase can result in muddy (unclear) bass or even a complete cancellation in the frequency response. Therefore,
both the MRD-M300 and MRD-M500 are equipped with Digital Time Correction, making it possible to realign
subwoofer(s) in time. Proper use of this function will result in clear, powerful bass with a smooth transition to the
other speakers in the system. It is recommended to use the calculation formula provided in the owner's manual as a
starting point for this adjustment.
Congratulations on your new V12AccuClass-D
TM
amplifier purchase. Before you get started, there are a few things
you should know about this unique amplifier that will help you optimize performance for your personal tastes or
particular application. Unlike traditional designs, the V12 AccuClass-D
TM
amplifier employs a completely digital
internal architecture, utilizing both advanced DSP (digital signal processing) and amplification technologies. This
innovative design not only offers unparalleled tuning capability and accuracy, but also allows direct digital coupling
to the power output stage for cleanest and most powerful bass possible. As with any amplifier however, proper
setup is essential if you are to maximize your listening experience. Please read the quick explanation and setup
procedure for each feature listed on the following pages.
Important notes:
To maximize the output power from this amplifier, you must use a 2 ohm load.
Before adjusting the amplifier settings, set the signal source (head-unit) level to
minimize distortion.
It is best to utilize music that will represent your typical heavy bass listening
scenario when adjusting levels.
V12 AccuClass-D
Setup Guide
For MRD-M300, MRD-M500 and MRD-M1000 Amplifiers
STEP 7. (7) PHASE
Phase control allows you to flip the polarity of the subwoofer without actually reversing the physical connections.
This convenient feature is useful when the subwoofer is in a position that could result in some cancellation, causing
diffused, unclear bass. It is recommended to try both settings (0
°
/180
°
) to determine which is best for your
particular system.
STEP 8. (8) AMP SET (Amplifier ID No. /Turn-On Delay)
The Amp Set menu performs two functions. Firstly, by setting the amplifier ID number (1-8), it allows the optional
RACC (RUX-4280 Remote Amplifier Control Center) to identify each amplifier individually and in a specific order.
Secondly, it provides a variable turn-on delay that can be used to minimize inrush current in large multi-amp
systems, or to eliminate any turn-on “pop”.
STEP 0. (0) MEMORY
Memory Mode allows you to store all amplifier settings in an auxiliary backup memory. Once stored, additional
tweaks or adjustments can be made while retaining the ability to recall the original settings at a later time. Note:
This is simply a convenience feature, since all settings are saved in real time as adjustments are made, and will
remain even if power is lost during setup.
STEP 9. (9) OUTPUT DISABLE
Previously known as “Safe Mode”, this feature provides a simple way to safely adjust the all DSP functions with the
amplification circuit turned off, eliminating the possibility of speaker damage during setup. When set to “ON”, it
literally disables the high current draw output stage of the amplifier, while leaving the input and processing
sections active. Please note that this is the only amplifier function that does not engage/disengage in real time,
but requires the remote lead to be cycled off/on for the selection to take effect. Therefore, if it is accidentally set to
“ON” during programming, there will be no output the next time the amplifier is activated. Additional uses include:
bench setup with a low current DC power supply, amp valet, tuning or troubleshooting larger multiple
amp/subwoofer systems, etc.
DISP
Toggle
ENT
ENT
• Press and depress the "MODE" button until you are
in mode "9" (Output Disable).
• Push "ENT" and push "ENT" again to select "9-1" (ON/OFF).
• Toggle until "OFF" is displayed.
• Push "DISP" to exit.
Note: This setting will not take effect until the amp is
turned off and then on again.
SETTING SAFE MODE TO "OFF"
START HERE
1) Output Disable is on:
Go to Step 9 (Mode 9 on the amp) and set to “OFF”, then cycle amp power.
2)
Subsonic and LPF frequency selections overlap or are too close together:
Adjust the crossover properly
3) If using RUX-4280 (RACC) remote subwoofer level is turned down :
Make sure the RACC is in normal
display mode (voltage or temperature) and adjust the level control.
4) Defective or broken RCA cables):
Replace RCA connectors
5) Blown fuse:
Replace Fuse with proper value
6) Remote trigger is not active:
Check remote turn-on lead with a voltage meter
7) Bad ground or power connection:
Check and replace ground connector
Typical causes for little or no output
NOTE: If using a RUX-4280 (RACC) with more than 1 AccuClass-D amplifier, be sure to set each amplifier with a
different ID Number (1-8). Amplifiers with the same ID will cause the RACC to display "NO AMP."
F
I
N
I
S
H
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alpine mrd m 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alpine mrd m 500 in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info