541351
5
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
GL3300 U
G
UIDE
5
EARTHING THE AUDIO SYSTEM
The console chassis is connected to mains earth via the DC power cable. Audio 0V is connected to the
chassis and therefore mains earth. In this way all signal returns and connector shields are connected to
mains earth at the console.
To ensure operator safety do not remove the earth connection
from the power supply mains plug.
For best performance it is important that the earth system is solid, clean and noise-free. To prevent mains
born and external interference pickup from lighting equipment, motors and other mains powered
equipment it is recommended that a separate 'clean' mains distribution outlet is used for the audio system.
All signal cables should have their screens connected to earth at the connector. If earth (ground) loop
problems result in audible hum or buzz then disconnect the cable screen connection at one end, usually the
destination end. This may be done within the cable plug or by operating the 'ground lift' switch if available
on the connected equipment. Many DI boxes and power amplifiers include this facility.
PLUGGING UP THE CABLES
Where possible use balanced connections to prevent noise and interference pickup especially on long
microphone cable runs. Avoid running audio cables next to mains, computer or lighting cables, or near
thyristor dimmer units, power supplies etc. The use of low impedance sources such as good quality
microphones of 200 ohms or less significantly reduces interference pickup. Many problems can be avoided
by taking time to check that all cables are correctly wired (in-phase) with professional quality cable and
carefully soldered joints. The following wiring convention is used:
Switch off the input channel +48V when using non-phantom
powered, line or unbalanced sources.
F
ADJUSTING THE LEVELS
For best performance it is important that the connected source signals are matched to the "normal operating
level" of the console. Similarly the console outputs should be correctly matched to the operating levels
of the connected amplifiers and destination equipment. If too high the signal peaks will be clipped
resulting in a harsh distorted sound, and if too low the signal-to-noise ratio is reduced resulting in excessive
background hiss.
For best results operate the console with the meters averaging '0' or just below and allowing the loudest
passages and occassional peaks into the 'yellow'. Reduce the gain if the peak indicators flash (red). The
GL3300 produces a standard XLR output level of +4dBu for a meter reading of 0VU. It is advisable to
adjust the power amplifier input gain or fit an attenuator pad if normal console operation results in an output
level too high for the connected amplifier. Normal operation should result in fader levels around the '0'
mark.
The GL3300 has an advanced PFL (pre-fade listen) / AFL (after-fader listen) and channel metering
system to let you listen to and check the level of signals at different points in the signal path without
affecting the main outputs. Use the channel PFL switches to set up the input GAIN controls to read an
average '0' (yellow LED). Signal activity is always shown on the channel meters regardless of fader mute
switch position. The green 'SIG' LED lights at -20dBu to indicate signal presence, the green '0' LED
indicates normal level, and the red 'PEAK' LED warns of potential overload 5dB before clipping.
XLR pin 1 = 0V earth shield
pin 2 = hot (+ve - in phase signal)
pin 3 = cold (-ve - out of phase signal)
1/4" jack tip = hot / +ve/signal / left / send
ring = cold /-ve/ 0V / right/ return
sleeve = 0V earth shield
To connect an unbalanced source to a balanced console input, link the cold input (XLR pin 3 or jack ring)
to 0V earth (pin 1 or jack sleeve) at the console. To connect a balanced console output to an unbalanced
destination link the cold output to 0V earth at the console.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Allen-Heath GL 3300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Allen-Heath GL 3300 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info