541362
37
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
GL2400 User Guide 37
Output balance options The aux and matrix
outputs are impedance balanced as standard
operating at nominal -2dBu and with +20dBu
maximum drive. They provide similar interference
rejection to electronically balanced outputs when
connected to balanced equipment inputs. An
electronically balanced option is available if you
require nominal +4dBu and higher output drive up
to +26dBu over very long cable runs. However, it is
not usually necessary to fit this option as the
impedance balanced drive satisfies most
applications. Check that you really need the option
before fitting it.
There are two balanced driver ICs which may be
used. Either is suitable. These are available from
Allen & Heath or good electronic component
suppliers. The Allen & Heath part number is shown
below:
SSM2142P A&H Part AE0302
DRV134 A&H Part AE5725
For each aux master, snip the legs of the two zero
ohm resistor links next to the IC socket. This
removes them from the circuit. Now simply plug the
option IC into the socket. Observe the correct IC
pin1 orientation and make sure its legs are correctly
aligned with the socket. Test the output once the
work is complete. You should measure the same
level but opposite polarity signal between + (hot)
and ground, and – (cold) and ground.
Sys-Link V2 input/output option
A blank
plate is fitted here as standard. This may be
replaced with an optional card which provides the
console inputs, outputs and PFL system on two
37way D connectors for linking to other Allen &
Heath consoles already fitted with Sys-Link V2. The
GL2400 can become an input channel expander
(slave) or have its number of input channels
expanded (master) when linked to other consoles.
A 37way shielded multi-core cable carries the
balanced mix signals and PFL/AFL system to or from
the other console.
IMPORTANT: Note that you need a 37 to 25way
adapter cable if you are connecting Sys-Link V2
(Version 2) to the older Sys-Link V1 (Version 1)
standard.
For full details please refer to the Sys-Link option
Applications Note AP6050 and Fitting Instructions
AP6049.
SLAVE CONSOLE
GL2400
SYS-LINK V2 OUTPUT
GL2400 OR OTHER A&H CONSOLE
SYS-LINK V2 INPUT
MASTER CONSOLE
37WAY CABLE
SYS-LINK V2 OUTPUT SYS-LINK V2 INPUT
MASTER L
AUX5
BALANCE
GROUP
MATRIX 1-4
BALANCE
AUX 1-4
BALANCE
MASTER R
AUX6
BALANCE
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Allen-Heath GL 2400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Allen-Heath GL 2400 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info