668915
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
INTRODUCTION
The Alecto DVM-67 is a wireless audio/video baby monitor,
suitable for private use indoors.
You can either watch and listen continuously or you can have
the baby monitor switch on automatically as soon as your
baby starts crying.
The Alecto DVM-67 meets all essential requirements and
other provisions as described in the European Directive
1999/5/EC.
The declaration of conformity is available
on the website www.alecto.nl
Use of this equipment is allowed in all countries of the EU. In
France, Italy, Russia and Ukraine, only indoor use is allowed.
ATTENTION
Before you start using the set, please remove any protective
foil from the parent unit and baby unit.
ICONS ON THE DISPLAY
upper part of the display, during normal use
indicates the reception strength:
strong reception
good reception
average reception
bad reception
receiver is searching for a camera
no camera detected
x
(x = 1 ~ 4) shows which camera you are viewing
‘monitoring mode’ (setup choice to view cameras one after
the other when using multiple cameras)
volume set to 0 (speaker turned off)
VOX is activated (unit switches on automatically when the
baby starts crying)
temperature display of the baby room
battery indication:
battery is empty
battery is full
animation while the bat-
tery is charging
appears when the adaptor is connected and the battery is
not or incorrectly installed
icons on the display during setup
this icon is followed by the number of registered cameras
which you can select using the and buttons
in this menu, you can set the display brightness
here you can set the sensitivity level for the VOX function
in this menu, you can turn the VOX function on or off
here you can choose to have the temperature shown in
degrees Celsius or degrees Fahrenheit
in this menu, you can register additional cameras on the
receiver
INSTALLATION
BABY UNIT:
Power:
1. Connect one of the
supplied 6V power
adaptors to the 6V
DC input of the baby
unit.
2. Insert the adapter into
a 230V wall socket.
Only use the supplied power adaptor with model number
S003IV0600060.
Wall-mounting:
Drill two holes next to each other in the
wall separated by a distance of 5.4cm
and insert plugs and screws. The head
of the screw should stick out of the wall
for several millimeters.
Slide the foot of the baby unit over the
screws and then press the baby unit a
little downwards.
Tips for placement:
For use as a baby monitor:
place the baby unit at least
1-2 meters away from your
baby and make sure to safely
tuck away the adapter cable.
For optimal range, it is advis-
able to set up the baby unit
as high as possible, free from large metal surfaces.
The temperature protrudes from the rear of the baby unit.
Make sure this sensor hangs freely, unexposed to direct
sunlight and avoid heat from e.g. light bulbs.
The baby unit is not waterproof. When using outdoors,
make sure to protect the baby unit against moisture and
sand.
PARENT UNIT:
Power supply:
The parent unit can be powered directly by the included re-
chargeable battery or via the supplied power adapter. As soon
as you connect the power adapter, it will charge the battery
allowing for mobile use of the parent unit.
Battery:
1. Open the battery com-
partment by sliding and
clicking off the battery
cover at the rear.
2. Connect the battery
plug in the battery
compartment according
to the gure below and
install the battery.
Only install
the supplied
rechargeable NiMH bat-
tery (3.6V, 900mAh).
Never connect the plug
or install the battery by
force.
3. Click the battery cover
back onto the parent
unit.
Power adapter:
1. Connect
the other
6V power
adapter to
the DC6V
input on the
side of the
parent unit.
(behind the
rubber cover
top)
2. Insert the adapter into a 230V wall socket.
Only use the supplied power adaptor with model number
S003IV0600060.
You can recharge the battery with the parent unit either
switched on or off, although charging the battery with the
parent unit switched off will take less time.
Charging:
The battery will be charged as soon as you connect the power
adapter and insert it into a 230V wall socket.
For initial use, charge the battery for at least 15 hours,
even if the indicator shows a fully charged battery.
The charging circuit for the battery is managed electroni-
cally and there is no risk of overcharging, this allows you
to leave the adapter connected at all times.
In case you will not use the set for a longer period of time
(>2 months), please make sure to disconnect the adapter
from the wall socket and remove the battery from the par-
ent unit. When starting to use the set again, make sure to
properly charge the battery.
Make sure nobody can trip or fall over the adapter cable.
You can bundle cables that are too long with tape or
cables ties available specically for this purpose.
Battery indication:
Upper part of the display: (only with the parent unit switched
on)
: no battery installed, parent unit is powered directly
through the adaptor
: battery is full
: battery is nearly empty
: battery is charging
Middle part of the display: (only with the parent unit switched
on)
: this symbol appears for several seconds every minute
in the last hour before the battery is exhausted.
Indicator on the parent unit:
ashes in red: battery nearly empty
remains red: battery is charging (turns off when the bat-
tery is full)
Lanyard:
You can attach a lanyard
or wristband at the top of
the parent unit. A lanyard or
wristband is not included.
USER MANUAL
DVM-67
PARENT UNIT:
1. visual sound indica-
tion, also displays the
volume level while
adjusting
2. power button, press
briey to turn the
display on or off,
press and hold for
2 seconds to turn the
parent unit on or off
3. battery indicator (see
also further in this
user manual)
4. power adaptor input
5. zoom in/out,
6. power indicator
7. function button:
MENU/SELECT:
to open the menu and
to conrm selections
VOL , VOL , and
: various functions,
see this user manual
8. talk-back button to-
wards the baby unit
9. built-in microphone
10. Battery compartment
11. suspending option for
wrist band
12. built-in speaker
13. foldable stand
FUNCTIONS OVERVIEW
BABY UNIT:
1. Infra-red LEDs
(for night vision)
2. indicator light,
switched off when
the baby unit is
turned off, ashes
while the baby
unit is searching
for the parent
unit, remains lit
when the baby
unit is in commu-
nication with the
parent unit
3. power adaptor
input
4. power button
5. light sensor
6. camera lens
7. Volume increase
8. PAIR button (to
pair this baby unit
with the parent
unit)
9. Volume decrease
10. built-in micro-
phone
11. Built-in speaker
12. Temperature
sensor
13. Ball coupling
hinge for proper
camera orienta-
tion
14. camera feet
1
2
1
2
3
1
2
>1 - 2 m
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alecto DVM-67 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alecto DVM-67 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Alecto DVM-67

Alecto DVM-67 Gebruiksaanwijzing - Nederlands - 2 pagina's

Alecto DVM-67 Gebruiksaanwijzing - Deutsch - 2 pagina's

Alecto DVM-67 Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info