794846
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2 sensor type: Non-dispersive infrared sensor
5. CO2 sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2 Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10. CO2 concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10. The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2 Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2 & Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2 display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alecto AQ30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alecto AQ30 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1.88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info