708462

Alecto ADB-11 Handleiding

1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
ADB-11 Installation
1 2
1 2
Outdoor-unit:
Indoor-unit:
It is very important to install and operate this product according to the following instructions.
Failure to do so may render your guarantee void.
Accessories List
The door chime kit comes with:
● 1 x Receiver ● 1 x Transmitter
● 1 x 3 volts CR2032 battery for transmitter ● 1 x Double-sided adhesive tape
● 1 x Instruction Manual
Pictures for Accessories
Model NO: QH-840A
WIRELESS DOOR CHIME KIT INSTRUCTION MANUAL
Auto-learning Code Door Chime
Names for Parts
(1) Melody Selector (2) Volume Button (3) Hanging Hole
(4) Speaker (5) Battery Cover (6) Push Button
(7) Nameplate Cover
(8) Silica gel stopper and screw
(9) Front cover and back cover hook (10) Standby holes for screws
(11) Interface
Notes before Installation
1. Before installation and operation, you will require a drill, a cross-headed screwdriver, a flat head
screwdriver, fixing screws and wall plugs. All of these are not supplied with this kit.
2. Avoid the Transmitter positioning on Metal Frames.
3. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or
bathroom.
How to use the door chime kit?
Pressing the Transmitter, a wireless signal will be sent to the Receiver. The Receiver will be activated
and sound. The operating range is 100m ( in the open air ) and you can use the Receiver virtually
anywhere at home (only indoor use). However, the transmission range will be reduced if the signal
is transmitted through a number of walls or ceilings and Metal or UPVC doorframes can also reduce
the operating range.
Battery Installation
Transmitter Unit
1. Remove the nameplate cover.
2. Take out the silica gel stopper with thin-tipped tweezers or needle.
3. Screw off the screw by using a screwdriver.
4. Insert a flat screwdriver into the slot on the bottom of the transmitter and turn to open the
front cover.
5. Install a 3V CR2032 battery matching the polarity (+ side up).
6. Close the front cover.
7. Lock the screw and silica gel stopper back into the hole.
8. Put the nameplate cover back.
Receiver Unit
Remove the battery cover and insert 2×1.5V AA batteries; Ensure battery polarity macth the
internal markings.
Auto-learning Code Set Up
The door chime kit is equipped with an auto-learning code ability. Please see detailed operation
Auto-learning Code Set Up in the manual.
Nameplate
There is a nameplate position on each Transmitter. It is for user’s signature on it as identification.
User needs to remove the nameplate cover and put a suitable size label with his / her name or other
information. Then cover it. (Label is not included.)
Important
1. Receiver is designed for indoor use only.
2. Do not mount the Transmitter onto any metal surface or UPVC doorframes, as this will reduce the
operation range.
3. Do not expose either unit directly to rain or immerse in water.
4. Do not mount either unit close to fireplace or expose to high temperature.
5. If leaving the chime for long periods, remove the battery from compartment to prevent leakage.
6. Dispose of old batteries in accordance with the relevant legislation.
User Hints
If the Receiver does not sound, please check the following:
● Flat batteries in either Transmitter or Receivers-change the batteries.
● Wrong battery polarity in either Transmitter or Receivers-reinsert the batteries.
● Units are out of range-Operate the Receiver within the operation range.
Specification
A. Transmitter unit
Power: 1×3volts CR2032 battery
B. Receiver unit
Power: 2x1.5 volts AA alkaline batteries
Operating Temperature: -20°C to +40°C
Operating Distance: 100 meters in the open field (328ft approx.-in open field and suitable conditions)
Selectable Tone: Total 36 melodies available
Digital Code Type: Auto-learning
What is Auto-learning Code?
The Transmitter sends wireless signal to the Receiver. The Receiver would automatically register and
memorize the signal as an operation code. So the Transmitter can work with the Receiver by this code.
Auto-learning Code Set Up
The Door Chime Kit is equipped with auto-learning operation code ability.
1. Operation for 1 transmitter and 1 receiver
After battery installation on both Transmitter and Receiver, press the Transmitter once to generate
a new operation code. The Receiver will sound, which indicates that a new operation code is
registered and memorized.
2. Operation for 2 transmitters and 1 receiver
After battery installation on the two Transmitters firstly and then Receiver, press the push button
on each Transmitter once within 15 seconds to generate new operation codes. The Receiver will
sound, which indicates that two new operation codes are registered and memorized. This is the
only way for the 2 Transmitters to work with the Receiver.
(If user press the push button on each Transmitter after 15 seconds, only the first Transmitter will
generate a new operation code and the Receiver will sound to indicate the first operation code is
registered and memorized.)
3. Interference from another door chime operating nearby (For example, Receiver sounds for no
reason):
Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory. Insert
the batteries, and then the Transmitters and the Receiver are ready for the new code registration.
4. Operation for the 3rd / 4th / 5th Transmitters and the receiver (There is 2 Transmitters included):
(a) Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory.
(b) Load the batteries into the Transmitters and Receiver, and the Receiver is ready for the new code
registration.
(c) Press the Transmitters once per each within 15 seconds, they will individually generate new
operation codes randomly and send wireless signals to the Receiver which will sound to indicate
that new operation codes are registered and memorized. (The Receiver has 15 seconds to learn
maximum 5 operation codes after batteries are installed. If there is no operation code sent from
Transmitter within 15 seconds, the Receiver would be only ready for 1 new code registration. It
means, only the 1st Transmitter can work with 1 Receiver after 15 seconds.)
(d) It is important to remember that when you replace the run-out batteries with new ones that you
will need to follow the same procedure of the auto-learning code set-up as above.
Notes:
(a) If the Receiver sounds for no reason during the digital code setting, it is indicated that it has been
interfered by other similar Door Chime nearby, reset the auto-learning code as per point 3 above.
(b) 1 Receiver can only work with maximum 5 Transmitters at the same time. If the Transmitter is
missing, terminal user can buy the only Transmitter from store and set up the auto-learning code
as instruction above.
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN
REPLACING BATTERIES
1 2 3
4 5 6
Transmitter Double-side
adhesive
Instruction ManualCR2032
Battery
Receiver front side Receiver back side
(1)
(2)
(5)
(3)
(4)
Receiver
2x1.5V AA
Alkaline Battery
Transmitter Unit
1. Open the Transmitter with screw driver and separate the front cover from back covers, as
mentioned before. Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. Mounting on UPVC or metal doorframe surfaces will
reduce the transmitting range. (As picture 1)
2. Or you can stick the Transmitter with the double-sided adhesive tape. (As picture 2)
1
2
Receiver Unit
Fix a screw on the wall. Then hang the Receiver by the hole at the
back of the unit. Avoid positioning on UPVC Frames, above heat
sources (e.g. radiator) or in damp areas such as a kitchen or bathroom.
Important: Test the Receiver before drilling any holes to ensure it
is within operating range.
Note: As an alternative, the Receiver can also be placed on the flat surface, such as table.
Functions Instruction
Door Chime Operation
Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which
will sound. The sound will stop as soon as the melody ends. For repeat sound, press the button again.
Hold the button in will NOT repeat the sound.
Melody Selection
There is a melody selector located at right side of the door chime. Press the selector to change
different melody.
Volume Adjustment
There is a volume button at right side of the door chime. Press it to adjust the sound volume to be
high, medium and low.
Receiver
(11)
(10)
(9)
(7)
(8)
(6)
Transmitter front
cover outside
Transmitter back
cover inside
CR2032 Battery
Wall Mount
To install you will require a drill and cross-headed screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are not cables or pipes
that you may accidentally damage.
It is very important to install and operate this product according to the following instructions.
Failure to do so may render your guarantee void.
Accessories List
The door chime kit comes with:
● 1 x Receiver ● 1 x Transmitter
● 1 x 3 volts CR2032 battery for transmitter ● 1 x Double-sided adhesive tape
● 1 x Instruction Manual
Pictures for Accessories
Model NO: QH-840A
WIRELESS DOOR CHIME KIT INSTRUCTION MANUAL
Auto-learning Code Door Chime
Names for Parts
(1) Melody Selector (2) Volume Button (3) Hanging Hole
(4) Speaker (5) Battery Cover (6) Push Button
(7) Nameplate Cover
(8) Silica gel stopper and screw
(9) Front cover and back cover hook (10) Standby holes for screws
(11) Interface
Notes before Installation
1. Before installation and operation, you will require a drill, a cross-headed screwdriver, a flat head
screwdriver, fixing screws and wall plugs. All of these are not supplied with this kit.
2. Avoid the Transmitter positioning on Metal Frames.
3. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or
bathroom.
How to use the door chime kit?
Pressing the Transmitter, a wireless signal will be sent to the Receiver. The Receiver will be activated
and sound. The operating range is 100m ( in the open air ) and you can use the Receiver virtually
anywhere at home (only indoor use). However, the transmission range will be reduced if the signal
is transmitted through a number of walls or ceilings and Metal or UPVC doorframes can also reduce
the operating range.
Battery Installation
Transmitter Unit
1. Remove the nameplate cover.
2. Take out the silica gel stopper with thin-tipped tweezers or needle.
3. Screw off the screw by using a screwdriver.
4. Insert a flat screwdriver into the slot on the bottom of the transmitter and turn to open the
front cover.
5. Install a 3V CR2032 battery matching the polarity (+ side up).
6. Close the front cover.
7. Lock the screw and silica gel stopper back into the hole.
8. Put the nameplate cover back.
Receiver Unit
Remove the battery cover and insert 2×1.5V AA batteries; Ensure battery polarity macth the
internal markings.
Auto-learning Code Set Up
The door chime kit is equipped with an auto-learning code ability. Please see detailed operation
Auto-learning Code Set Up in the manual.
Nameplate
There is a nameplate position on each Transmitter. It is for user’s signature on it as identification.
User needs to remove the nameplate cover and put a suitable size label with his / her name or other
information. Then cover it. (Label is not included.)
Important
1. Receiver is designed for indoor use only.
2. Do not mount the Transmitter onto any metal surface or UPVC doorframes, as this will reduce the
operation range.
3. Do not expose either unit directly to rain or immerse in water.
4. Do not mount either unit close to fireplace or expose to high temperature.
5. If leaving the chime for long periods, remove the battery from compartment to prevent leakage.
6. Dispose of old batteries in accordance with the relevant legislation.
User Hints
If the Receiver does not sound, please check the following:
● Flat batteries in either Transmitter or Receivers-change the batteries.
● Wrong battery polarity in either Transmitter or Receivers-reinsert the batteries.
● Units are out of range-Operate the Receiver within the operation range.
Specification
A. Transmitter unit
Power: 1×3volts CR2032 battery
B. Receiver unit
Power: 2x1.5 volts AA alkaline batteries
Operating Temperature: -20°C to +40°C
Operating Distance: 100 meters in the open field (328ft approx.-in open field and suitable conditions)
Selectable Tone: Total 36 melodies available
Digital Code Type: Auto-learning
What is Auto-learning Code?
The Transmitter sends wireless signal to the Receiver. The Receiver would automatically register and
memorize the signal as an operation code. So the Transmitter can work with the Receiver by this code.
Auto-learning Code Set Up
The Door Chime Kit is equipped with auto-learning operation code ability.
1. Operation for 1 transmitter and 1 receiver
After battery installation on both Transmitter and Receiver, press the Transmitter once to generate
a new operation code. The Receiver will sound, which indicates that a new operation code is
registered and memorized.
2. Operation for 2 transmitters and 1 receiver
After battery installation on the two Transmitters firstly and then Receiver, press the push button
on each Transmitter once within 15 seconds to generate new operation codes. The Receiver will
sound, which indicates that two new operation codes are registered and memorized. This is the
only way for the 2 Transmitters to work with the Receiver.
(If user press the push button on each Transmitter after 15 seconds, only the first Transmitter will
generate a new operation code and the Receiver will sound to indicate the first operation code is
registered and memorized.)
3. Interference from another door chime operating nearby (For example, Receiver sounds for no
reason):
Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory. Insert
the batteries, and then the Transmitters and the Receiver are ready for the new code registration.
4. Operation for the 3rd / 4th / 5th Transmitters and the receiver (There is 2 Transmitters included):
(a) Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory.
(b) Load the batteries into the Transmitters and Receiver, and the Receiver is ready for the new code
registration.
(c) Press the Transmitters once per each within 15 seconds, they will individually generate new
operation codes randomly and send wireless signals to the Receiver which will sound to indicate
that new operation codes are registered and memorized. (The Receiver has 15 seconds to learn
maximum 5 operation codes after batteries are installed. If there is no operation code sent from
Transmitter within 15 seconds, the Receiver would be only ready for 1 new code registration. It
means, only the 1st Transmitter can work with 1 Receiver after 15 seconds.)
(d) It is important to remember that when you replace the run-out batteries with new ones that you
will need to follow the same procedure of the auto-learning code set-up as above.
Notes:
(a) If the Receiver sounds for no reason during the digital code setting, it is indicated that it has been
interfered by other similar Door Chime nearby, reset the auto-learning code as per point 3 above.
(b) 1 Receiver can only work with maximum 5 Transmitters at the same time. If the Transmitter is
missing, terminal user can buy the only Transmitter from store and set up the auto-learning code
as instruction above.
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN
REPLACING BATTERIES
1 2 3
4 5 6
Transmitter Double-side
adhesive
Instruction ManualCR2032
Battery
Receiver front side Receiver back side
(1)
(2)
(5)
(3)
(4)
Receiver
2x1.5V AA
Alkaline Battery
Transmitter Unit
1. Open the Transmitter with screw driver and separate the front cover from back covers, as
mentioned before. Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. Mounting on UPVC or metal doorframe surfaces will
reduce the transmitting range. (As picture 1)
2. Or you can stick the Transmitter with the double-sided adhesive tape. (As picture 2)
1
2
Receiver Unit
Fix a screw on the wall. Then hang the Receiver by the hole at the
back of the unit. Avoid positioning on UPVC Frames, above heat
sources (e.g. radiator) or in damp areas such as a kitchen or bathroom.
Important: Test the Receiver before drilling any holes to ensure it
is within operating range.
Note: As an alternative, the Receiver can also be placed on the flat surface, such as table.
Functions Instruction
Door Chime Operation
Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which
will sound. The sound will stop as soon as the melody ends. For repeat sound, press the button again.
Hold the button in will NOT repeat the sound.
Melody Selection
There is a melody selector located at right side of the door chime. Press the selector to change
different melody.
Volume Adjustment
There is a volume button at right side of the door chime. Press it to adjust the sound volume to be
high, medium and low.
Receiver
(11)
(10)
(9)
(7)
(8)
(6)
Transmitter front
cover outside
Transmitter back
cover inside
CR2032 Battery
Wall Mount
To install you will require a drill and cross-headed screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are not cables or pipes
that you may accidentally damage.
3
It is very important to install and operate this product according to the following instructions.
Failure to do so may render your guarantee void.
Accessories List
The door chime kit comes with:
● 1 x Receiver ● 1 x Transmitter
● 1 x 3 volts CR2032 battery for transmitter ● 1 x Double-sided adhesive tape
● 1 x Instruction Manual
Pictures for Accessories
Model NO: QH-840A
WIRELESS DOOR CHIME KIT INSTRUCTION MANUAL
Auto-learning Code Door Chime
Names for Parts
(1) Melody Selector (2) Volume Button (3) Hanging Hole
(4) Speaker (5) Battery Cover (6) Push Button
(7) Nameplate Cover
(8) Silica gel stopper and screw
(9) Front cover and back cover hook (10) Standby holes for screws
(11) Interface
Notes before Installation
1. Before installation and operation, you will require a drill, a cross-headed screwdriver, a flat head
screwdriver, fixing screws and wall plugs. All of these are not supplied with this kit.
2. Avoid the Transmitter positioning on Metal Frames.
3. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or
bathroom.
How to use the door chime kit?
Pressing the Transmitter, a wireless signal will be sent to the Receiver. The Receiver will be activated
and sound. The operating range is 100m ( in the open air ) and you can use the Receiver virtually
anywhere at home (only indoor use). However, the transmission range will be reduced if the signal
is transmitted through a number of walls or ceilings and Metal or UPVC doorframes can also reduce
the operating range.
Battery Installation
Transmitter Unit
1. Remove the nameplate cover.
2. Take out the silica gel stopper with thin-tipped tweezers or needle.
3. Screw off the screw by using a screwdriver.
4. Insert a flat screwdriver into the slot on the bottom of the transmitter and turn to open the
front cover.
5. Install a 3V CR2032 battery matching the polarity (+ side up).
6. Close the front cover.
7. Lock the screw and silica gel stopper back into the hole.
8. Put the nameplate cover back.
Receiver Unit
Remove the battery cover and insert 2×1.5V AA batteries; Ensure battery polarity macth the
internal markings.
Auto-learning Code Set Up
The door chime kit is equipped with an auto-learning code ability. Please see detailed operation
Auto-learning Code Set Up in the manual.
Nameplate
There is a nameplate position on each Transmitter. It is for user’s signature on it as identification.
User needs to remove the nameplate cover and put a suitable size label with his / her name or other
information. Then cover it. (Label is not included.)
Important
1. Receiver is designed for indoor use only.
2. Do not mount the Transmitter onto any metal surface or UPVC doorframes, as this will reduce the
operation range.
3. Do not expose either unit directly to rain or immerse in water.
4. Do not mount either unit close to fireplace or expose to high temperature.
5. If leaving the chime for long periods, remove the battery from compartment to prevent leakage.
6. Dispose of old batteries in accordance with the relevant legislation.
User Hints
If the Receiver does not sound, please check the following:
● Flat batteries in either Transmitter or Receivers-change the batteries.
● Wrong battery polarity in either Transmitter or Receivers-reinsert the batteries.
● Units are out of range-Operate the Receiver within the operation range.
Specification
A. Transmitter unit
Power: 1×3volts CR2032 battery
B. Receiver unit
Power: 2x1.5 volts AA alkaline batteries
Operating Temperature: -20°C to +40°C
Operating Distance: 100 meters in the open field (328ft approx.-in open field and suitable conditions)
Selectable Tone: Total 36 melodies available
Digital Code Type: Auto-learning
What is Auto-learning Code?
The Transmitter sends wireless signal to the Receiver. The Receiver would automatically register and
memorize the signal as an operation code. So the Transmitter can work with the Receiver by this code.
Auto-learning Code Set Up
The Door Chime Kit is equipped with auto-learning operation code ability.
1. Operation for 1 transmitter and 1 receiver
After battery installation on both Transmitter and Receiver, press the Transmitter once to generate
a new operation code. The Receiver will sound, which indicates that a new operation code is
registered and memorized.
2. Operation for 2 transmitters and 1 receiver
After battery installation on the two Transmitters firstly and then Receiver, press the push button
on each Transmitter once within 15 seconds to generate new operation codes. The Receiver will
sound, which indicates that two new operation codes are registered and memorized. This is the
only way for the 2 Transmitters to work with the Receiver.
(If user press the push button on each Transmitter after 15 seconds, only the first Transmitter will
generate a new operation code and the Receiver will sound to indicate the first operation code is
registered and memorized.)
3. Interference from another door chime operating nearby (For example, Receiver sounds for no
reason):
Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory. Insert
the batteries, and then the Transmitters and the Receiver are ready for the new code registration.
4. Operation for the 3rd / 4th / 5th Transmitters and the receiver (There is 2 Transmitters included):
(a) Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory.
(b) Load the batteries into the Transmitters and Receiver, and the Receiver is ready for the new code
registration.
(c) Press the Transmitters once per each within 15 seconds, they will individually generate new
operation codes randomly and send wireless signals to the Receiver which will sound to indicate
that new operation codes are registered and memorized. (The Receiver has 15 seconds to learn
maximum 5 operation codes after batteries are installed. If there is no operation code sent from
Transmitter within 15 seconds, the Receiver would be only ready for 1 new code registration. It
means, only the 1st Transmitter can work with 1 Receiver after 15 seconds.)
(d) It is important to remember that when you replace the run-out batteries with new ones that you
will need to follow the same procedure of the auto-learning code set-up as above.
Notes:
(a) If the Receiver sounds for no reason during the digital code setting, it is indicated that it has been
interfered by other similar Door Chime nearby, reset the auto-learning code as per point 3 above.
(b) 1 Receiver can only work with maximum 5 Transmitters at the same time. If the Transmitter is
missing, terminal user can buy the only Transmitter from store and set up the auto-learning code
as instruction above.
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN
REPLACING BATTERIES
1 2 3
4 5 6
Transmitter Double-side
adhesive
Instruction ManualCR2032
Battery
Receiver front side Receiver back side
(1)
(2)
(5)
(3)
(4)
Receiver
2x1.5V AA
Alkaline Battery
Transmitter Unit
1. Open the Transmitter with screw driver and separate the front cover from back covers, as
mentioned before. Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. Mounting on UPVC or metal doorframe surfaces will
reduce the transmitting range. (As picture 1)
2. Or you can stick the Transmitter with the double-sided adhesive tape. (As picture 2)
1
2
Receiver Unit
Fix a screw on the wall. Then hang the Receiver by the hole at the
back of the unit. Avoid positioning on UPVC Frames, above heat
sources (e.g. radiator) or in damp areas such as a kitchen or bathroom.
Important: Test the Receiver before drilling any holes to ensure it
is within operating range.
Note: As an alternative, the Receiver can also be placed on the flat surface, such as table.
Functions Instruction
Door Chime Operation
Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which
will sound. The sound will stop as soon as the melody ends. For repeat sound, press the button again.
Hold the button in will NOT repeat the sound.
Melody Selection
There is a melody selector located at right side of the door chime. Press the selector to change
different melody.
Volume Adjustment
There is a volume button at right side of the door chime. Press it to adjust the sound volume to be
high, medium and low.
Receiver
(11)
(10)
(9)
(7)
(8)
(6)
Transmitter front
cover outside
Transmitter back
cover inside
CR2032 Battery
Wall Mount
To install you will require a drill and cross-headed screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are not cables or pipes
that you may accidentally damage.
It is very important to install and operate this product according to the following instructions.
Failure to do so may render your guarantee void.
Accessories List
The door chime kit comes with:
● 1 x Receiver ● 1 x Transmitter
● 1 x 3 volts CR2032 battery for transmitter ● 1 x Double-sided adhesive tape
● 1 x Instruction Manual
Pictures for Accessories
Model NO: QH-840A
WIRELESS DOOR CHIME KIT INSTRUCTION MANUAL
Auto-learning Code Door Chime
Names for Parts
(1) Melody Selector (2) Volume Button (3) Hanging Hole
(4) Speaker (5) Battery Cover (6) Push Button
(7) Nameplate Cover
(8) Silica gel stopper and screw
(9) Front cover and back cover hook (10) Standby holes for screws
(11) Interface
Notes before Installation
1. Before installation and operation, you will require a drill, a cross-headed screwdriver, a flat head
screwdriver, fixing screws and wall plugs. All of these are not supplied with this kit.
2. Avoid the Transmitter positioning on Metal Frames.
3. Avoid positioning above heat sources such as radiators, or in damp areas such as a kitchen or
bathroom.
How to use the door chime kit?
Pressing the Transmitter, a wireless signal will be sent to the Receiver. The Receiver will be activated
and sound. The operating range is 100m ( in the open air ) and you can use the Receiver virtually
anywhere at home (only indoor use). However, the transmission range will be reduced if the signal
is transmitted through a number of walls or ceilings and Metal or UPVC doorframes can also reduce
the operating range.
Battery Installation
Transmitter Unit
1. Remove the nameplate cover.
2. Take out the silica gel stopper with thin-tipped tweezers or needle.
3. Screw off the screw by using a screwdriver.
4. Insert a flat screwdriver into the slot on the bottom of the transmitter and turn to open the
front cover.
5. Install a 3V CR2032 battery matching the polarity (+ side up).
6. Close the front cover.
7. Lock the screw and silica gel stopper back into the hole.
8. Put the nameplate cover back.
Receiver Unit
Remove the battery cover and insert 2×1.5V AA batteries; Ensure battery polarity macth the
internal markings.
Auto-learning Code Set Up
The door chime kit is equipped with an auto-learning code ability. Please see detailed operation
Auto-learning Code Set Up in the manual.
Nameplate
There is a nameplate position on each Transmitter. It is for user’s signature on it as identification.
User needs to remove the nameplate cover and put a suitable size label with his / her name or other
information. Then cover it. (Label is not included.)
Important
1. Receiver is designed for indoor use only.
2. Do not mount the Transmitter onto any metal surface or UPVC doorframes, as this will reduce the
operation range.
3. Do not expose either unit directly to rain or immerse in water.
4. Do not mount either unit close to fireplace or expose to high temperature.
5. If leaving the chime for long periods, remove the battery from compartment to prevent leakage.
6. Dispose of old batteries in accordance with the relevant legislation.
User Hints
If the Receiver does not sound, please check the following:
● Flat batteries in either Transmitter or Receivers-change the batteries.
● Wrong battery polarity in either Transmitter or Receivers-reinsert the batteries.
● Units are out of range-Operate the Receiver within the operation range.
Specification
A. Transmitter unit
Power: 1×3volts CR2032 battery
B. Receiver unit
Power: 2x1.5 volts AA alkaline batteries
Operating Temperature: -20°C to +40°C
Operating Distance: 100 meters in the open field (328ft approx.-in open field and suitable conditions)
Selectable Tone: Total 36 melodies available
Digital Code Type: Auto-learning
What is Auto-learning Code?
The Transmitter sends wireless signal to the Receiver. The Receiver would automatically register and
memorize the signal as an operation code. So the Transmitter can work with the Receiver by this code.
Auto-learning Code Set Up
The Door Chime Kit is equipped with auto-learning operation code ability.
1. Operation for 1 transmitter and 1 receiver
After battery installation on both Transmitter and Receiver, press the Transmitter once to generate
a new operation code. The Receiver will sound, which indicates that a new operation code is
registered and memorized.
2. Operation for 2 transmitters and 1 receiver
After battery installation on the two Transmitters firstly and then Receiver, press the push button
on each Transmitter once within 15 seconds to generate new operation codes. The Receiver will
sound, which indicates that two new operation codes are registered and memorized. This is the
only way for the 2 Transmitters to work with the Receiver.
(If user press the push button on each Transmitter after 15 seconds, only the first Transmitter will
generate a new operation code and the Receiver will sound to indicate the first operation code is
registered and memorized.)
3. Interference from another door chime operating nearby (For example, Receiver sounds for no
reason):
Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory. Insert
the batteries, and then the Transmitters and the Receiver are ready for the new code registration.
4. Operation for the 3rd / 4th / 5th Transmitters and the receiver (There is 2 Transmitters included):
(a) Remove the batteries from the Receiver and rest for 30 seconds, this will erase the memory.
(b) Load the batteries into the Transmitters and Receiver, and the Receiver is ready for the new code
registration.
(c) Press the Transmitters once per each within 15 seconds, they will individually generate new
operation codes randomly and send wireless signals to the Receiver which will sound to indicate
that new operation codes are registered and memorized. (The Receiver has 15 seconds to learn
maximum 5 operation codes after batteries are installed. If there is no operation code sent from
Transmitter within 15 seconds, the Receiver would be only ready for 1 new code registration. It
means, only the 1st Transmitter can work with 1 Receiver after 15 seconds.)
(d) It is important to remember that when you replace the run-out batteries with new ones that you
will need to follow the same procedure of the auto-learning code set-up as above.
Notes:
(a) If the Receiver sounds for no reason during the digital code setting, it is indicated that it has been
interfered by other similar Door Chime nearby, reset the auto-learning code as per point 3 above.
(b) 1 Receiver can only work with maximum 5 Transmitters at the same time. If the Transmitter is
missing, terminal user can buy the only Transmitter from store and set up the auto-learning code
as instruction above.
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN
REPLACING BATTERIES
1 2 3
4 5 6
Transmitter Double-side
adhesive
Instruction ManualCR2032
Battery
Receiver front side Receiver back side
(1)
(2)
(5)
(3)
(4)
Receiver
2x1.5V AA
Alkaline Battery
Transmitter Unit
1. Open the Transmitter with screw driver and separate the front cover from back covers, as
mentioned before. Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. Mounting on UPVC or metal doorframe surfaces will
reduce the transmitting range. (As picture 1)
2. Or you can stick the Transmitter with the double-sided adhesive tape. (As picture 2)
1
2
Receiver Unit
Fix a screw on the wall. Then hang the Receiver by the hole at the
back of the unit. Avoid positioning on UPVC Frames, above heat
sources (e.g. radiator) or in damp areas such as a kitchen or bathroom.
Important: Test the Receiver before drilling any holes to ensure it
is within operating range.
Note: As an alternative, the Receiver can also be placed on the flat surface, such as table.
Functions Instruction
Door Chime Operation
Press the push button on the Transmitter unit once, it sends a wireless signal to the Receiver which
will sound. The sound will stop as soon as the melody ends. For repeat sound, press the button again.
Hold the button in will NOT repeat the sound.
Melody Selection
There is a melody selector located at right side of the door chime. Press the selector to change
different melody.
Volume Adjustment
There is a volume button at right side of the door chime. Press it to adjust the sound volume to be
high, medium and low.
Receiver
(11)
(10)
(9)
(7)
(8)
(6)
Transmitter front
cover outside
Transmitter back
cover inside
CR2032 Battery
Wall Mount
To install you will require a drill and cross-headed screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are not cables or pipes
that you may accidentally damage.
4 5
1

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Alecto-ADB-11

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alecto ADB-11 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alecto ADB-11 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info