630548
85
Verklein
Vergroot
Pagina terug
1/373
Pagina verder
85
Recording Automation
Tip: To make automating certain parameters easier, assign certain parameters to the Q-Link Knobs as
described in the next section rather than adjusting them in their respective modes. We also recommend
using your MPC hardware (especially the Q-Link Knobs) whenever possible.
1. Determine where the parameter you want to automate is—Main Mode, Program Mixer Mode, or
Track Mixer Mode—and click the Main Mode, Program Mixer Mode, or Track Mixer Mode tab to
enter that mode.
2. If the desired parameter is Program- or pad-related, click the Program's
Automation button (curve icon) until it turns red and has a W. This means the Program
is able to record (write) automation. In Main Mode and Track Mixer Mode, this button is
on the Program Channel Strip. In Program Mixer Mode, this is in the Master Section.
Program- or pad-related parameters include: Program Channel Strip controls, Pad/Keygroup
insert effects, Program insert effects, send effects, Master Semi Tune, Master Fine Tune, and all
pad parameters shown in Program Edit Mode.
If the desired parameter is Track-related, skip to the next step.
Track-related parameters include: Track Channel Strip controls, MIDI CC messages, Track
mutes, pad mutes, the 16-Level feature (on the MPC hardware), Aftertouch messages, Pitchbend
messages, Channel Pressure messages, Program Change messages, and parameters shown in the
Main Mode's Q-Link section's Param menu when set to Prg and Change is set to Note On.
3. Click the Overdub button, and then click Play to start automation recording. It is very important to
use the Overdub function; otherwise, this new recording will overwrite any data previously recorded
to that Track.
4. Move the desired control(s)
during the recording process.
The automation curve will
appear as you move the
control(s).
5. Click Stop you are finished recording.
Tip: After recording, we highly recommend clicking the Automation button on the
Program Channel strip so it turns green and has an R. This means the Program will read
automation but will not record any additional automation over it, though you can still
manually edit and enter automation.
85

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Akai MPC Software bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Akai MPC Software in de taal/talen: Engels als bijlage per email.

De handleiding is 20,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info