630573
168
Verklein
Vergroot
Pagina terug
1/170
Pagina verder
156
Appendix
IDE/SCSI Conversion Kit
With the IDE/SCSI Conversion Kit, the IDE hard disk drive can be connected to the internal 50-pin SCSI
connector of the DPS12.
Consult your AKAI professional dealer where you purchased or the AKAI professional Service Center
for the installation of disk drive.
The self-installation may cause serious damages to both the disk drive and DPS12.
Notes:
Use ERASE, instead of FORMAT, to format the IDE drive. The IDE drive may freeze when FORMAT is
performed.
When ERASE is performed on the IDE disk that has been used on other device or brand new disk, an
error message may appear. In this case, perform ERASE again.
Consult your AKAI professional dealer or AKAI professional Service for the drives that can be installed.
Installation - To Service Technicians
IDE/SCSI Conversion Kit Installation
Install the IDE/SCSI Conversion Kit included to the IDE drive by the following procedure. The rest will be the
same as that of SCSI drive.
Note: Set the IDE drive in Master Mode referring to the drive’s manual.
Contents:
ID2SC PC board .................................................................. 1
PCB Mounting Bracket (L), (R) ............................................ 1
40P IDE flat cable ................................................................ 1
4P power cable .................................................................... 1
Plastic rivet........................................................................... 4
Drive Mounting screw (inch-thread 3.2 x 5) ......................... 8
Drive Mounting Plate screw (3 x 10) .................................... 4
Washer (2mm) ..................................................................... 4
ID2SC PCB Installation
1. Attach the PCB Mounting Bracket (L) and (R) to the IDE drive as illustrated. Refer to the direction of ID
hole to the connectors on the IDE drive. Use four inch-thread screws to fix them.
2. Connect the 40P IDE flat cable and 4P power cable to the ID2SC PC board. Place the cables between the
IDE drive and ID2SC PC board and fix the PC board to the PCB Mounting Brackets with plastic rivets.
Care must be taken to avoid pinching the wires by the PC board.
3. Connect the other end of cables to the IDE drive.
4. Set the DIP switch to the default setting as shown.
168

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Akai DPS12i bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Akai DPS12i in de taal/talen: Engels als bijlage per email.

De handleiding is 2,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info