496440
15
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
En
ENGLISH
15
DOLBY SURROUND AND DTS
SURROUND
ADJUSTING SPEAKER LEVEL
BALANCE
SUBWOOFER
+,-
CENTER
+,-
REAR +,-
BALANCE
BALANCE
JOG +,-
MANUAL
SELECT
The unit is equipped with a built-in test signal generator called a
noise sequencer for easy balance adjustment of all five channels.
The sequencer outputs a noise signal that “travels” from channel
to channel, enabling the simple adjustment of sound level to
achieve the same apparent loudness, at your listening position,
from each channel.
Preparation
Before adjusting the speaker level balance, be sure to set
the speaker size, distance and existance correctly.
Before adjusting the speaker level balance, turn off the DSP
surround system.
Operate the unit while playing the source recorded in Dolby
Digital surround or Dolby Pro Logic.
1Turn SURROUND on.
2 Press and hold MANUAL SELECT on the remote
control until “L” of “L/R 0dB” starts to flash.
A noise signal is sent to each channel in turn at the interval of
2 seconds as follows:
L/R 0dB
C 0dB
L/R 0dB
S 0dB
S 0dB
*L or R flashes to indicate one of the front speakers from
which the noise signal is output.
3 Adjust the sound level of the center and surround
speakers.
While “C” or “S” flashes in the display, press JOG + or - on
the remote control so that the sound level of the center or
surround speakers matches that of the front speakers.
The blance of the front speakers can be adjusted as well while
L/R” is displayed.
4 Press MANUAL SELECT again to stop the noise
signal.
NOTE
When the noise signal cycles through all the speakers for ten
times, the noise singal stops automatically.
When the center speaker and/or surround speakers are set to
NONE”, their level balance cannot be adjusted. (“C 0dB” and “S
0dB” are not displayed.)
About the channels
The left and right front speakers create the stereo effect.
The center speaker helps precise sound positioning over a broad
sound field.
The surround speakers enhance the “depth” of the sound field.
CHANGING SPEAKER VOLUME
TEMPORARILY
According to the software played or your preference, you can
change the sub woofer, center speaker and surround speakers
volume temporarily.
Press SUBWOOFER +/-, CENTER +/- or REAR +/-
on the remote control.
Each speaker level can be changed within the range from –10
dB to +10 dB at 1 dB steps.
To restore the volume and balance to the default value
Press and hold BALANCE until “LVL RESET” is displayed.
All the speaker volume as well as the left and right balance of
the front and surround speakers are reset to the default value
(0 dB).
(Left front speaker)*
(Center speaker)
(Right front speaker)*
(Right surround speaker)
(Left surround speaker)
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aiwa AV-NW31 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aiwa AV-NW31 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info