28958
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
MX-3
MX-3
MX-3
MX-3
MX-3
MX-3
Get The Advantage
3 Channel Computer
Radio System
MODEL
BATT
REV
ARC
SUB-T
MODEL
EPAD/R
TH
H
L
L R
ST
B
/
DSC
1
2
3
Super Micro
3 CH. Receiver
92836 75 FM
Mhz
#1 #2 #3
Steering
Throttle
AUX
B/DSC
Switch
AA Dry Cell Battery Holder
Mechanical Speed Controller
B
/
DSC
1
2
3
Super Micro
3 CH. Receiver
92836 75 FM
Mhz
#2
Electronic Speed Controller
ESC
TRANSMITTER BATTERY INSTALLATION
RECEIVER AND SERVO CONNECTIONS
Your MX-3 Computer R/C system receiver is NOT
equipped with BEC circuitry. DO NOT use more
than 6.0 volts to power the receiver. Anything higher
than 6.0 volts will burn-up or destroy your receiver.
Only use a 4.8~6.0 volt battery pack or a speed
controller that is designed to lower the voltage to
the receiver. The following diagram shows a typical
connection for the servos and receiver.
Note that the receiver antenna should be located at
least 2” (50mm) away from any servo leads and
switches. In electric cars, we recommend that it be
at least 4” (100mm) from the electric motor.
Extend the receiver antenna to the full length. Failure
to do so will cause loss of control. Do not cut or bend the
receiver antenna.
Insulate the connectors with tape or use tie wraps to
avoid contact with metal car chassis.
Please follow the model manufactures recommendations
for the correct installation of your radio system in your
car or boat.
Switch
To Battery
To Motor
!
CAUTION
When installing your MX-3 radio
system in your model, always
make sure to set your model on
a stand so the wheels are free
from any traction before turning
on your radio and or connecting
your motor for the first time.
TRIGGER POSITION ADJUSTMENT
Throttle Trigger Set
Screw
Throttle Trigger Position Gauge
A
B
Throttle Trigger Adjustment screw
NOTE:
Trigger Set Screw must be
loosened before adjusting
The Throttle Trigger can be adjusted to
give you a more natural feel of the throttle.
To Adjust:
1. Loosen the Throttle Trigger set screw
by turning counter clock-wise.
2. Turning the adjustment screw clock-wise
will move the trigger out or in the (A)
direction.
3. Turning the adjustment screw counter
clock-wise will move the trigger in or
towards the (B) direction.
4. After adjustment is made, re-tighten
the Trigger Set Screw.
5. Total adjustment for the trigger is 10mm.
Do Not over tighten adjustment screw,
it may damage the adjuster and or
the threads.
TROUBLESHOOTING GUIDE and WARNINGS
If your radio system does not operate properly, please
check the following items:
1. Make sure the batteries are properly installed and
fully charged. With alkaline batteries, make certain
the batteries are installed in the correct direction.
2. Check that both the transmitter and receiver power
switches are in the ON position.
3. Check the battery voltage by turning on the transmitter
and pushing both menu bottons at the same time
and releasing.
4. Make sure that the proper frequency crystals are
installed in both the transmitter and receiver.
5. Make sure all the receiver and servo connections
are tight.
WARNINGS:
DO NOT OPERATE YOUR SYSTEM IF SOMEONE
ELSE IS ON YOUR FREQUENCE AT THE SAME TIME.
YOUR MODEL CAN CAUSE SERIOUS DAMAGE OR
INJURY SO PLEASE USE CAUTION AND COURTESY
AT ALL TIMES.
DO NOT EXPOSE THE RADIO SYSTEM TO WATER
OR EXCESSIVE MOISTURE.
PLEASE WATER PROOF THE RECEIVER AND SERVOS
BY PLACING THEM IN A WATER TIGHT RADIO BOX
WHEN OPERATING R/C BOAT MODELS.
IF YOU HAVE LITTLE OR NO EXPERIENCE OPERATING
R/C MODELS, WE STRONGLY RECOMMEND YOU SEEK
THE ASSISTANCE OF EXPERIENCED MODELERS OR
YOUR LOCAL HOBBY SHOP FOR GUIDANCE.
To Open slide Cover Install Batteries To Close slide cover
Press down on the battery cover and slide
in the direction of the arrow to remove.
Install 8 pieces “AA” size alkaline batteries as
indicated on the battery tray. Make sure to match
the polarity (+ and -) as shown in the battery
compartment or the transmitter will not function.
Install the battery cover in place and slide to close.
1.
2.
3.
WARNING: Improper installation of transmitter batteries
can cause serious damage to your system.
To Battery
To Motor
DIGITAL CONTROL SYSTEM
+
-
INC / DEC
MENU
ESC
REGISTRATION NUMBER
The abbreviation, IC, before the registration number signifies that registration was performed based on a
Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not
imply that Industry Canada approved the equipment.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Airtronics MX3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Airtronics MX3 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info