429063
5
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
61180019L1-5A Issue 1, May 2004 5
All permanent connections to the Total Access 1500 19-
Inch Chassis are made on the backplane. Figure 4 is a
detailed diagram of the power and ground connectors,
and Figure 5 is an illustration of the backplane and
pinouts.
Figure 4. Power and Ground Connectors
Frame Ground Connection
The frame ground terminal, located on the upper right
corner of the backplane (see Figure 4 and Figure 5),
should be connected using appropriately sized wire. Use
a wire gauge that is at least the same gauge as the power
wiring.
To make the frame ground connection to the Total
Access 1500 19-Inch Chassis, perform the following
steps:
1. Using the crimping tool, connect an appropriate
lug to each end of the appropriately sized wire.
2. Connect the ground wire from Total Access 1500
19-Inch Chassis ground terminal on
TB1 to the
equipment rack grounding screw.
3. Tighten the ground connection securely with a
straight-slot screwdriver.
Test Frame Ground Connection
To ensure a good ground, use a multimeter to check
continuity between the frame grounding lug and the
rack grounding strap at the top of the rack. Using an
ohmmeter set to its the lowest resistance range, place
one lead on the rack’s ground strap and the other lead on
the Total Access 1500 19-Inch Chassis ground terminal
on
TB1. The reading should be 1 or 2 ohms. Greater
readings should be investigated.
Power Connection
NOTE
Connect to a reliably grounded –48 VDC
source, which is electrically isolated from the
AC source.
NOTE
A readily accessible disconnect device, such as
a rackmount fuse and alarm panel that is
suitably approved and rated, should be incor-
porated in the fixed wiring.
Power connections use a block, labeled
TB1, located on
the upper right side of the backplane (see Figure 4 and
Figure 5). The terminals are on 0.375 inch centers and
allow for wire gauges up to 12 AWG. The frame ground
terminal routes to mechanical contact points and
provides an electrical connection to the chassis
metalwork. The power bus and frame ground route to all
the modules in the chassis.
The number of Total Access 1500 19-Inch Chassis that
can be placed in a 7-foot CO rack depends on the type
of service deployed and the number of access modules
in the chassis.
After connecting and checking the ground to the Total
Access 1500 19-Inch Chassis, connect power to the
chassis. Check to make sure the power source is
providing the correct power and polarity to the Total
Access 1500 19-Inch Chassis. The following steps
provide instructions on how to connect power to the
chassis.
1. Determine which fuse pairs are to supply power to
the Total Access 1500 19-Inch Chassis.
2. Remove the fuses from the A and B slots for the
pair.
3. The power terminal is labeled
TB1. Cut four
lengths of appropriately sized wire to reach from
the terminals on the fuse and alarm panel to the
power terminals on the Total Access 1500 19-Inch
Chassis.
4. Using the crimping tool, connect an appropriate
lug to each end of the wires.
TB1
Pin Number Description
TB1
IN
IN
RTN
RTN
IN RTN
-48V PRI
IN RTN
-48V SEC
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Adtran total access 1500 quad line interface unit bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Adtran total access 1500 quad line interface unit in de taal/talen: Engels als bijlage per email.

De handleiding is 4,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info