Press the EQ SETUP button to display the current
setting of EQ Band 1.
Press the
EQ SETUP button again to select next EQ Band.
Press the
Vol+ or Vol- button to increase or decrease
the volume for current EQ Band.
Press
EQ SETUP button to store the new EQ setting.
Press
EQ ON/OFF button to switch the new EQ settings on or off.
AEGOp5 Operation - DRC
(Dynamic Range Compression)
DRC
Your AEGOP5 features Dynamic Range
Compression (DRC), its sophisticated
technology creates realistic sound fields
with richly detailed sound that is
remarkably free from distortion.
Repeatedly pressing DRC button will
switch between 3 modes:
“NO” No compression is applied to the
original audio signal, this provides the
greatest dynamic range.
“HALF” Partial compression is applied, this
function is useful if AEGO
P5 is connected
to an external amplifier.
“FULL” Full compression is applied, this function is useful
if AEGO
P5 is connected to an external amplifier.
Press the
DRC button to display the current setting of Dynamic
Range Compression mode.
Press the
DRC button again to switch between the DRC modes.
DOLBY DIGITAL CO
DYNAMIC HALF
DOLBY DIGITAL CO
DYNAMIC FULL
DOLBY DIGITAL CO
DYNAMIC NO
DOLBY DIGITAL CO
EQ BAND 2 +01DB
DOLBY DIGITAL CO
EQ BAND 2 0DB
DOLBY DIGITAL CO
EQ BAND 1 0DB
AEGOp5 Operation
- Resetting
Resetting
Your AEGOP5 can be reset to its factory
default settings by pressing
RESET button
on the remote.
Press the
RESET button to reset the
AEGO
P5 to its factory default settings.
When completed, your AEGO
P5 reverts
to Auto Decode mode.
DOLBY DIGITAL CO
SURROUND
DOLBY DIGITAL CO
RESET TO FACTORY
AEGOp5 Operation
15
AEGOp5 Operation
- Saving Presets
Setting Presets
The AEGOP5 enables you to customise
up to 4 settings. This function enables
you to save and load your favourite
settings at any time.
Saving a Preset:
Press the PRESET 1 button, the display
will show the following:
Press the
SAVE button to save all the
current decoder settings into Preset 1.
When complete, your AEGO
P5 will revert back to Auto Decode mode.
AEGOp5 Operation
- Loading Preset
Loading a Preset
You can load a previously saved preset
by pressing
LOAD button on the
remote.
Loading a Preset:
Press any of the 4 preset buttons,
(PRESET 1, PRESET 2, PRESET 3 or
PRESET 4), the display will show
the following:
Press
LOAD button to load the preset.
When preset loading is complete, your AEGO
P5 will revert back to
Auto Decode mode.
DOLBY DIGITAL CO
DOLBY DIGITAL CO
PRESET 1 LOADED
DOLBY DIGITAL CO
PRESET 1 LOADING
DOLBY DIGITAL CO
PRESET 1
DOLBY DIGITAL CO
DOLBY DIGITAL CO
PRESET 1 SAVED
DOLBY DIGITAL CO
PRESET 1 SAVING
DOLBY DIGITAL CO
PRESET 1
AEGOp5 Operation
- Sound Field Processing
DSP Sound Field
Your AEGOP5 is equipped with a sound
field processor that gives you six
different field effects; Disable, Hall,
Theater, Stadium, Club, and Church. By
pressing
Field button on the remote,
you can select any of these effects. You
can also increase or decrease the
Reverb value from 0 - 9 by pressing
VOL + or VOL - on the remote control
whilst you are selecting the field effect.
Press the Field button and repeat to
change the current setting of Sound Field mode.
AEGOp5 Operation
- Equalization
5-Band Equalization
Your AEGOP5 features a 5-band equalizer
which enables you to fine tune the sound
of your favourite movie or music. Press
EQ SETUP button on the remote to
activate it. Repeatedly pressing
EQ SETUP
button will switch between the 5 bands.
Each band of the equalizer enables you to
adjust your desired volume to a maximum
of ±10dB. Press
VOL + or VOL - on the
remote control to adjust the volume.
After setting the desired volume for each
EQ band, you
press EQ SETUP button again to store the
new setting for that band.
Press EQ ON/OFF button to switch the new EQ settings on or off.
DOLBY DIGITAL CO
CHURCH REVERB 3
DOLBY DIGITAL CO
CLUB REVERB 3
DOLBY DIGITAL CO
STADIUM REVERB 3
DOLBY DIGITAL CO
THEATRE REVERB 3
DOLBY DIGITAL CO
HALL REVERB 3
DOLBY DIGITAL CO
DIABLE REVERB 0
AEGOp5 Operation
14
