756348
2
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
UK
MK4100
Installation instructions Magnetic contact for gates and doors
Introduction
Top-class, heavy-duty contact for gates and doors. Extremely robust aluminium design highly-resistant to breakages (e.g.
when driven over by forklifts). VdS Class C certified.
Advantages of the magnetic contacts
High resistance to environmental conditions
Very large switching intervals
Extremely high resistance to wear
Simple installation
Installation
Installation is primarily made on roll-up, sliding and tilting gates and doors.
Before installation, determine the installation location so that the door contact and magnet can be fitted as shown in fig. 2.
The contact casing is fitted on the floor (a flat mounting surface is necessary).
Otherwise, only screws made of non-ferromagnetic materials may be used.
The weatherproof and mechanically stable construction of the contact casing protects the switching mechanism from
damage when driven over by vehicles with rubber tyres. To protect the product from greater loads, it must be embedded
into the ground.
The four-core cable is protected by a stainless steel protective sleeve. Two hose clips with screws and wall plugs are
included in the installation set for laying the metal sleeve properly away from the door or gate area.
When fitting the magnet casing, note the position of the two screw-holes on the contact casing, as shown in fig. 1. These
two holes determine the exact lateral position of the magnet relative to the contact.
The spacing between the contact casing and magnet casing should measure approximately 5-25 mm (as shown in the
diagram). If ferromagnetic materials are present in the immediate vicinity, then the switching areas must be specially
determined. The magnet should always be fitted in the middle of the non-operational area whilst adhering to VdS fitting
guidelines.
During installation, pay attention to the movement tolerance of the movable fitting surface for the magnet casing.
After installation is completed, the electrical functions on the contact must be checked (e.g. ohmmeter or circuit tester).
Warning:
The magnet loses some of its field strength if exposed to intense
heat or vibrations. This can also happen if it is placed near another
magnet and like poles are placed together.
Technical data:
Housing material: Aluminium
Cable: 2 m (double-insulated: 4 x 0.14 mm²)
Connections: NC, max. contact capacity
60 V DC / 300 mA / 3 W
Temperature with fixed cables: -25 °C to +70 °C
Temperature with movable cables: -5 °C to +50 °C
Protection class: IP 65
Optimal spacing between sensors: 5-25 mm
VdS Class B: G 198067
Functional diagram
Floor
Magnet switch
Fig. 2
Fig. 1
Door
Floor
Magnet switch
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Abus mk4100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Abus mk4100 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info