556865
6
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
6
2
Converting (see illustration B)
The position, the burner type (upper case character) and the tap (lower case character) are schematically indicated
on the sticker in the bottom layer. There are small bags with the corresponding characters in the conversion set
(see “Introduction”).
1. Replace the injectors in the burners. Use a tubular spanner 7 for disassembling/assembling the injector
(see illustrations B1, B2 en B3).
2. Replace the simmer setting screws in the taps. The position of the simmer setting screw can vary per type of
gas tap (see illustration B4). Use a screwdriver, blade width 4 mm, for disassembling/assembling of the simmer
setting screw (see illustration B5/B6) and when necessary use pliers.
3. On the wok burner, replace the injectors for simmer (G1), wok (G2) and roast (G3). The wok injector is
indicated by one rib on the injector holder, the roast injector by two ribs. The simmer injector is the one in the
middle (see illustrations B7 and B8). You can replace the simmer injector with a no. 7 open-end spanner and
a 3.6 Nm tightening moment. Use a no. 10 open-end spanner with a 5 Nm tightening moment to replace the
roast and wok injectors.
For verifi cation, you can fi nd the values of the injectors and simmer setting screws on the data label of this
se
t! For verifi cation also view the values table, injector and simmer setting screws.
4. Place the sticker ‘H1’ in the appropriate block on the current appliance identifi cation card (with the type of
gas/gas pressure) in the bottom tray (see illustrations B9, B10 and B11).
5. Place the sticker ‘H2’ in the appropriate block on the current appliance identifi cation card (with the type of
gas/gas pressure) on the underside of the bottom tray (see illustrations B9, B12 and B13).
6. Place the sticker ‘G2’ in the appropriate block on the current appliance identifi cation card (with the type of
gas/gas pressure) on the back of the user manual (see illustrations B9, B14 and B15).
Warning!
Check the appliance for gas tightness, especially the injectors and simmer setting screws!
Always check for gas tightness before using the appliance! Check the other injectors fi rst before checking
the roast injectors.
Please note: to do this, connect the appliance to the mains.
Do not forget to use the insulation plate!
B1
B2
B3
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ATAG HG9571MBA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ATAG HG9571MBA in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 2,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van ATAG HG9571MBA

ATAG HG9571MBA Installatiehandleiding - Nederlands - 2 pagina's

ATAG HG9571MBA Gebruiksaanwijzing - Nederlands - 34 pagina's

ATAG HG9571MBA Installatiehandleiding - Deutsch - 2 pagina's

ATAG HG9571MBA Gebruiksaanwijzing - Deutsch - 34 pagina's

ATAG HG9571MBA Installatiehandleiding - English - 2 pagina's

ATAG HG9571MBA Gebruiksaanwijzing - English - 34 pagina's

ATAG HG9571MBA Installatiehandleiding - Français - 2 pagina's

ATAG HG9571MBA Gebruiksaanwijzing - Français - 34 pagina's

ATAG HG9571MBA Installatiehandleiding - Dansk - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info