463270
2
Verklein
Vergroot
Pagina terug
1/57
Pagina verder
ENGLISH 2 WS 650-115, WS 715-115, WS 715-125, WSE 800-125
Introduction
You demand the best and buy quality - quality provided by Atlas Copco. We have
built for you a reliable and lasting tool. Working effectively and without endangering
your health is only possible if this instruction for use is read carefully before first us-
ing the tool. We want to satisfy our customers and would like you to buy again AEG
Electric Power Tools from Atlas Copco.
Technical Data
Safety advice Please pay attention to the safety instructions in the attached leaflet!
Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
Always disconnect the plug from the socket before carrying out any work on the ma-
chine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
Before use check machine, cable, and plug for any damages or material fatigue. Re-
pairs should only be carried out by authorised service agents.
Allow the machine to come to a stop before putting down.
Dust that arises when working in stones with crystalline silicic acid can damage your
health. Do not work on any material containing asbestos. Please note the safety reg-
ulations, VBG, of the employers liability insurance association.
Never reach into the danger area of the machine when it is running.
Always wear safety goggles and ear protectors when working with this machine. It
is further recommended to wear safety gloves, apron, as well as sturdy non-slipping
shoes.
Always use the additional handle.
Always use the protecting cap when roughing-down and separating.
Only use tools whose permitted speed is at least as high as the highest no-load
speed of the machine.
Check grinding tools before use. The grinding tool must be properly mounted and
turn freely. Perform a test run for at least 30 seconds without load. Do not use dam-
aged, out of round or vibrating grinding tools.
When grinding metal, flying sparks are produced. Take care that no persons are en-
dangered. Because of the danger of fire, no combustible materials should be locat-
ed in the vicinity (spark flight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust flying from the workpiece
come into contact with you.
Pay attention to the dimensions of the grinding disc. The mounting hole diameter
must fit the mounting flange without play. Do not use reducer pieces or adapters.
Never use a cutting disc for grinding. Do not subject cutting discs to side pressure.
When separating stone the guide shoe must be used!
Type WS 650- WS 715- WSE 800-
115 115 125 125
Nominal power (W) 650 710 710 800
Min. no-load speed (min
-1
) 2700
Max. no-load speed (min
-1
) 10000 10000 10000 10000
Grinding disk diameter (mm) 115 115 125 125
Thread of work spindle M14 M14 M14 M14
Weight (kg) 1,5 1,5 1,5 1,5
Speed control
No-load speed limiter
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw AEG WS 715-125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van AEG WS 715-125 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Fins als bijlage per email.

De handleiding is 1,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info