42029
27
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
24
D
ESCRIPTION
O
F
N
EW
F
UNCTIONS
Idling area
Point 1 is the stick maximum slow area. Therefore, adjust the idling mixture so that a
good idling speed is obtained. If the carburetor is still flooded when point 1 is 0%,
raise throttle curve point 1~2 and increase the air and readjust the throttle trimmer.
Set a value so that points 2 and 3 are connected to the hovering area.
Hovering area
Points 4~6 are the hovering area. Slowly hover and adjust the mixture while observ-
ing the hovering state. After hovering adjustment, land and take off and perform
climb adjustment. Next slowly climb from hovering and perform climb adjustment.
Adjust for the desired response so that the carburetor is not flooded within the points
4~6 range.
Flying range
Points 7~9 are the flying range. Point 9 is the maximum speed needle. Therefore,
adjust the connection from hovering to maximum speed with points 7 and 8. Slowly
set the throttle stick from hovering to full close and adjust the high side mixture. With
the stick fully closed, fly at high speed and set the needle, while paying attention to
the change in the sound. Finally, carry out hovering and flying adjustment and finish
by fine adjusting to the best mixture. When flying, the entire high side can be con-
trolled based on point 5 and needle changes caused by temperature changes can be
adapted to by using the VR set with the model menu (MDL) fuel mixture (FMC)
item.
5 Condition setup
(1) When the condition menu (CND) is called and the fuel mixture "FMC" function is
selected, the FUEL MIX item is displayed.
-This item enables setting of each condition. Set each condition matched to the number of conditions used.
CAUTION: Conditions setting is a condition.
(2) Set MST MIX MODE (master mix mode).
-This mode operates by mixing throttle and mixture. However, what is operated is decided individually. Usually,
this is used with "MIXED".
-When used with "MIXED", when the throttle curve is set, the mixture curve is simultaneously mixed and
changed. (The mixture curve can also be set in the mix mode "MIXED".)
-When used with "UNMIXED", throttle and mixture control are set independently. When a tuned silencer is used,
etc., the fuel can be adjusted independently and the adjustment width is widened. Since all mixture adjustments
are carried out independently, learn the functions before trying to make any adjustments.
(3) Set the mixture curve with the POINT item.
-Nine points, from point 1 to point 9, can be set. The smaller displayed value is the direction in which the needle
is closed and the larger displayed value is the direction in which the needle is opened.
-Set the basic curve data by referring to the values shown below. However, this setting is a little dense.
Reference values (OS carburetor)
(4) The setting range is divided into an idling area, hovering area, and flying area.
Point P1 P2 P3 P4 P5 P6 P7 P8 P9
Set value (%) 15 36 50 58 64 68 73 76 80
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw 9ZAP 9Z World Champion Model 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van 9ZAP 9Z World Champion Model 2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info