691438
2
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Installing the Transducer on a Trolling Motor
Assembling the Trolling Motor Barrel Mount Hardware
1
Align the top of the transducer with the top of the bracket
.
2
Using the included hex wrench, attach the bracket to the
transducer with the shoulder screw , rubber washer , and
flat washer .
NOTE: You must fully tighten the mount to the transducer.
The recommended torque applied to the shoulder screw is
2.5 lb-ft. (3.4 N-m).
Separating the Transducer Cables
Before you separate the cables, you should test-fit the
transducer. The cables should be at room temperature when
you separate them.
1
With the transducer dry fitted to the trolling motor, mark the
location the transducer cable crosses the rotating joint .
2
Place the transducer cables on a hard, flat surface.
3
Press the tip of the cutting tool, a flathead screwdriver, or a
blunt knife to the center of the cables at your marked
location, and puncture the material between the cables.
NOTE: Do not cut through or into the round section of the
cables. Puncture the center webbing between the cables
only.
4
Using your fingers, pull the cable halves apart approximately
12.5 cm (5 in.) on both sides of the hole.
5
Ensure the cables have a gap of at least 10 cm ( 4 in.) above
and 10 cm (4 in.) below the split portion of the cable and
are centered on the rotating joint . This creates a loop in
the cable over the rotating joint. The loop must be large
enough to allow full rotation of the transducer in both
directions. Allow a minimum of 25 cm (10 in.) of cable to
cover the 20 cm (8 in.) section between mounting points.
6
Use the black electrical tape to secure the transducer
cable to the shaft. The split section of the cable should
extend under the tape.
7
Test the full rotation of the trolling motor to ensure the cables
clear the rotating joint and are not pulled due to tension
during rotation.
Installing the Transducer on a Trolling Motor
NOTICE
You must secure the transducer cable to the shaft or other
secure location during installation. Damage to the transducer
cable wires or cable jacket can cause transducer failure.
1
Insert the hose clamp through the slot on the trolling motor
mount until equal lengths extend on both sides of the
mount.
2
Secure the hose clamp around the trolling motor .
NOTE: Do not rotate the transducer.
2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin Panoptix Livescope bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin Panoptix Livescope in de taal/talen: Engels als bijlage per email.

De handleiding is 2,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin Panoptix Livescope

Garmin Panoptix Livescope Installatiehandleiding - Nederlands - 6 pagina's

Garmin Panoptix Livescope Installatiehandleiding - Deutsch - 6 pagina's

Garmin Panoptix Livescope Installatiehandleiding - Français - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info