624831
7
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
Operation Guide 5325
E-48
After 10 lap times are recorded, the b Lower Dial Hand will point to the mark. This indicates that no
more lap times will be recorded.
If you perform a lap time operation that is not recorded (because 10 times are already in memory) and
that lap is the fastest lap, it will be recorded as the fastest lap.
Performing a new elapsed time operation after resetting the stopwatch will delete previously recorded
lap times.
An ongoing elapsed time measurement operation is not affected by pulling out the crown.
The x
Second Hand, which indicates the 1/20 (0.05)-second count during stopwatch operation, moves
only 30 seconds after an elapsed time measurement operation is started or restarted, or after a lap time
is cleared. After that, the x
Second Hand stops.
When elapsed time passes 60 minutes, the z
Hour Hand and v Upper Dial Hand will perform one full
rotation.
To recall lap data
1. While in the Stopwatch Mode, pull out the crown to enter the Data Recall Mode.
2. Rotate the crown to select other laps.
The b
Lower Dial Hand will indicate the lap number of currently shown time.
The b
Lower Dial Hand will indicate FL (fastest lap) when the fastest lap time is shown.
3. To return to the Stopwatch Mode, push the crown back in.
E-49
Using the Countdown Timer
The countdown timer can be confi gured within a range of one minute to 60 minutes. An alarm sounds for
about 10 seconds when the timer reaches zero.
Hands and Indicators
x Second Hand: Indicates countdown or elapsed seconds.
c Minute Hand: Indicates countdown or elapsed minutes.
b Lower Dial Hand: Points to TR.
All hands move counterclockwise during a countdown.

+
*
@
E-50
To specify the countdown start time
1. In the Timekeeping Mode, press C three times to enter the Countdown
Timer Mode.
The b
Lower Dial Hand will move to TR.
2. In the Countdown Timer Mode, pull out the crown. This enters the
countdown start time setting mode.
If you do not perform any operation with the crown for about two minutes
after pulling it out, crown operations will become disabled and the hand
will not move if you rotate the crown. If this happens, push the crown back
in and then pull it out again.
3. Rotate the crown to set the countdown start time.
The maximum countdown start time setting is 60 minutes. To set a
countdown start time of 60 minutes, move the c
Minute Hand to 12 o’clock.
See “Using the Crown” (page E-3) for information about high-speed hand
movement.

+
*
@
E-51
To perform a countdown timer operation
A
A B
Start Stop Zero Reset
A time-up alert sounds for 10 seconds when the countdown reaches 0, and then the timer displays the
start time.
The alarm will not sound if battery power is low.
Pulling out the crown while a countdown is in progress will stop the countdown and enter the
countdown start time setting mode.
Important!
Time calibration signal reception is disabled while the watch is in the Countdown Timer Mode.
To stop the alarm
Press any button.
E-52
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. This is true even if the watch is not in the Timekeeping
Mode.
Hands and Indicators
z Hour Hand: Indicates the currently set alarm time hour.
x Second Hand: Indicates the current alarm ON/OFF setting.
c Minute Hand: Indicates the currently set alarm time minute.
v Upper Dial Hand: Indicates the hour setting of the current alarm time in
24-hour format.
b Lower Dial Hand: Points to AL.

>
*B
+ @
E-53
To change the alarm time setting
1. In the Timekeeping Mode, press C four times to enter the Alarm Mode.
The b
Lower Dial hand will move to AL.
2. Pull out the crown to enter the alarm setting mode.
If you do not perform any operation with the crown for about two minutes after pulling it out, crown
operations will become disabled and the watch hands will no longer move when you rotate the
crown. If this happens, push the crown back in and then pull it out again.
You can toggle between the hour and minute setting mode, and the hour only setting mode by
pressing C.
Hour/Minute
Hour
C
3. Rotate the crown to set the alarm time.
The z Hour Hand will also move.
See “Using the Crown” (page E-3) for information about high-speed hand movement.
4. Press C to switch to the hour setting mode.
The z
Hour Hand will move slightly left and right to indicate the z Hour Hand setting mode.
Check the 24-hour time indicated by the v
Upper Dial Hand to see if the current setting is a.m. or
p.m.
5. Rotate the crown to adjust the hour setting only.
See “Using the Crown” (page E-3) for information about high-speed hand movement.
E-54
6. After the setting is the way you want, push the crown back in to exit the alarm setting mode.
The alarm always works based on the time kept in the Timekeeping Mode.
The watch will return to the Timekeeping Mode automatically if you do not perform any operation in
the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm between on and off. The x
Second Hand will indicate the
current ON/OFF setting.
Note
The alarm will not sound if battery power is low.
The alarm will not sound if the watch is in the Power Saving sleep state.
To stop the alarm
Press any button.
E-55
Adjusting Home Positions
Strong magnetism or impact can cause the hands and/or day indicator setting to be off, even if the watch
is able to perform the time calibration signal receive operation.
Auto Home Position Adjustment
Auto correction of hand home positions corrects the hand position automatically.
Auto correction is performed in the Timekeeping Mode only.
Auto correction corrects the positions of all hands. For the day Indicator, you must perform the manual
adjustment procedure under “To adjust home positions” (page E-56).
If the v
Upper Dial Hand is 12 hours off of the current correct time, correct the setting using the
procedure under “To adjust home positions” (page E-56).
Manual Home Position Adjustment
Perform the procedure in this section if auto home position adjustment is not possible for some reason.
Hand home position adjustment is not required if the time and day settings are correct.
Note
Any time after you enter the home position adjustment mode in step 2 of the following procedure, you
can return to the Timekeeping Mode by pushing the crown back in. In this case, any adjustments you
made before the watch returned to the Timekeeping Mode will be applied.
If you do not perform any operation with the crown for about two minutes after pulling it out, crown
operations will become disabled and hands will not move if you rotate the crown. If this happens, push
the crown back in and then pull it out again.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 5325 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 5325 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Casio 5325

Casio 5325 Gebruiksaanwijzing - Deutsch - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info