Handleiding Philips GC2920 (pagina 2 van 2) (Engels)

461752

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

Auto-off function (GC2960 only)

The auto-off function automatically switches off the iron if it has not been

moved for a while.

, Theredauto-offlightashestoindicatethattheironhasbeen

switched off by the auto-off function (Fig. 8).

To let the iron heat up again:

1 Pick up the iron or move it slightly.

, Theauto-offlightstopsashing.

, If the temperature of the soleplate has dropped below the set ironing

temperature, the temperature light goes on.

2 If the temperature light goes on after you have moved the iron, wait

for it to go out before you start ironing.

Note: If the temperature light does not go on after you move the iron, the

soleplate still has the right temperature and the iron is ready for use.

Cleaning and maintenance

Cleaning

1 Set the steam control to position 0, remove the plug from the wall

socket and let the iron cool down.

2 Wipeakesandanyotherdepositsoffthesoleplatewithadamp

cloth and a non-abrasive (liquid) cleaning agent.

To keep the soleplate smooth, avoid hard contact with metal objects.

Never use a scouring pad, vinegar or other chemicals to clean the soleplate.

3 Clean the upper part of the iron with a damp cloth.

4 Regularly rinse the water tank with water. Empty the water tank after

you have rinsed it (Fig. 9).

Double-Active Calc System (GC2960/GC2930/GC2920 only)

The Double-Active Calc System consists of an Anti-Calc tablet inside the

water tank combined with the Calc-Clean function.

- The Anti-Calc tablet prevents scale from clogging the steam vents. The

tablet is constantly active and does not need to be replaced (Fig. 10).

- The Calc-Clean function removes scale particles from the iron.

Calc-Clean function

Use the Calc-Clean function once every two weeks. If the water in your

area is very hard (i.e. when akes come out of the soleplate during ironing),

use the Calc-Clean function more frequently.

1 Make sure the appliance is unplugged.

2 Set the steam control to position 0.

3 Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents into the water tank.

4 Set the temperature dial to MAX (Fig. 11).

5 Put the mains plug in an earthed wall socket.

6 Unplug the iron when the temperature light goes out.

7 Hold the iron over the sink. Push the steam control to the Calc-Clean

position and hold it. Gently shake the iron to and fro (Fig. 12).

, Steam and boiling water come out of the soleplate. Impurities and

akes(ifany)areushedout.

8 Release the steam control as soon as all the water in the tank has

been used up.

9 Repeat the Calc-Clean process if the iron still contains a lot of impurities.

After the Calc-Clean process

1 Put the plug back into the wall socket and let the iron heat up to let

the soleplate dry.

2 Unplug the iron when the temperature light goes out.

3 Move the iron gently over a piece of used cloth to remove any water

stains that may have formed on the soleplate.

Storage

1 Set the steam control to position 0, remove the plug from the wall

socket and let the iron cool down.

2 Wind the mains cord round the cord storage facility (Fig. 13).

3 Store the iron on its heel in a safe and dry place.

Environment

- Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment (Fig. 14).

Guarantee & service

If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the worldwide

guarantee leaet). If there is no Consumer Care Centre in your country,

go to your local Philips dealer.

Troubleshooting

This chapter summarises the most common problems you could encounter

with the appliance. If you are unable to solve the problem with the

information below, contact the Consumer Care Centre in your country.

Problem Cause Solution

The iron is

plugged in, but the

soleplate is cold.

There is a connection

problem.

Check the mains cord, the plug and

the wall socket.

The temperature dial is

set to MIN.

Set the temperature dial to the

required position.

The iron does

not produce any

steam.

There is not enough

water in the water tank.

Fill the water tank (see chapter

‘Preparing for use’, section

‘Filling the water tank’).

The steam control is

set to position 0.

Set the steam position to l or ;

(see chapter ‘Using the appliance’,

section ‘Steam ironing’).

The iron is not hot

enough and/or the

drip-stop function has

been activated.

Set an ironing temperature that is

suitable for steam ironing ( 2 to

MAX). Put the iron on its heel and

wait until the temperature light goes

out before you start ironing.

The steam

boost function

does not work

properly.

You have used the steam

boost function too

often within a very

short period.

Continue ironing in horizontal

position and wait a while before you

use the steam boost function again.

The iron is not

hot enough.

Set an ironing temperature at which

the steam boost function can be

used ( 3 to MAX). Put the

iron on its heel and wait until the

temperature light goes out before

you use the steam boost function.

Flakes and

impurities come

out of the

soleplate during

ironing.

Hard water forms

akes inside the

soleplate.

Use the Calc-Clean function one or

more times (see chapter ‘Cleaning

and maintenance’, section ‘Calc-

Clean function’).

The light on the

handle ashes

(GC2960 only).

The auto-off function

has been activated

(see chapter ‘Features’,

section ‘Auto-off’).

Pick the iron up or move it slightly to

deactivate the auto-off function. The

auto-off light goes out.

Water droplets

drip on the

fabric during

ironing.

You have not closed

the cap of the lling

opening properly.

Press the cap until you hear a click.

The set temperature

is too low for steam

ironing.

Set an ironing temperature that is

suitable for steam ironing ( 2 to

MAX). Put the iron on its heel and

wait until the temperature light goes

out before you start ironing.

You have put an additive

in the water tank.

Rinse the water tank and do not put

any additive in the water tank.

You have used the

steam boost function at

a setting below 3.

Set the temperature dial to a setting

between 3 and MAX.

You have used the

steam boost function

too often within a

short period.

Continue ironing in horizontal

position and wait a while before you

use the steam boost function again.

Problem Cause Solution

Water drips

from the

soleplate after

the iron has

cooled down or

has been stored.

You have put the iron

in horizontal position

while there was still

water in the water tank.

Empty the water tank and set the

steam control to position 0 after use.

Store the iron on its heel.

Water spots

appear on the

garment during

ironing.

These wet spots may

be caused by steam

that has condensed

onto the ironing board.

Iron wet spots without steam from

time to time to dry them.

If the underside of the

ironing board is wet,

wipe it dry with a piece

of dry cloth.

To prevent steam from condensing

onto the ironing board, use an

ironing board with wire mesh top.

4239_000_7814_1_DFU-leaflet_A6_v4.indd 2 2/15/11 11:33 AM

Philips GC2920 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Andere handleiding(en) van Philips GC2920

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info