30018
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
RECEIVER FP-R107N & SERVO FP-S138
Receiver, servos, switches, and battery
connections
Extension cord
Receiver crystal
7-channel FM receiver FP-R107N
Antenna wire
Landing gear
adapter
Switch
SSW-J
Charging plug
NR-4J
Fig.
9
The parts enclosed by the
dotted lines must be
purchased separately.
6th
CH
servo
(6NLK
only)
Landing gear
servo
Landing gear
servo
Rudder
servo
Throttle
servo
Elevator
servo
Aileron
servo
PRECAUTIONS
Connect the
receiver,
servos,
switches, and
battery
firmly
as
shown in Fig. 9. Then extend the transmitter and receiver
antennas fully.
Set the transmitter power switch to ON. Then set the receiv-
er power switch to ON. The servos stop near the neutral
position. Operate the transmitter sticks and check that each
servo follows the movement of the stick.
•Connect the pushrod to each servo horn, then check if
the
direction of travel of each servo matches the direction
of
operation of
its
transmitter
stick.
To
reverse
the
direction
of servo travel, switch the servo reversing switch.
Operate each servo over its full stroke, and check if the push-
rod binds or is too loose. Applying unreasonable force to the
servo horn will adversely affect the servo and quickly drain
the battery. Always make the travel of each control mecha-
nism somewhat larger than the full travel (including trim) of
the servo horn. Adjust the servo horns so that they move
smoothly even when the trim lever and stick are operated
simultaneously in the same direction.
Be alert for noise.
This set is noise-resistant, but is not completely immune to
noise. We recommend the use of noiseless parts.
•When installing the switch harness, cut a rectangular hole
somewhat larger than the full stroke of the switch and install
the switch so that it moves smoothly from ON to OFF. This
also applies to the switch mount when the switch is installed
inside the fuselage and is turned on and off from the outside
with a piece of wire, etc. Install the switch where it will not
be exposed to engine oil, dust, etc.
Fig.
10
Wood screw
with flat
washer
Rubber
bushing
Grommet
Plywood,
FRP board,
Aluminum
sheet
Flat washer
Rubber
bushing
Grommet
(Using plywood, FRP, or
aluminum sheet)
SERVO MOUNTING
(Using wood screws)
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba FP5NLK bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba FP5NLK in de taal/talen: Engels als bijlage per email.

De handleiding is 1,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info