30018
3
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Elevator dual rate switch
This switch turns the
elevator dual rate function on and
off. The lower position is dual rate OFF and the upper
position is dual rate ON.
Elevator dual rate trimmer
This trimmer sets the elevator deflection angle when the
elevator dual rate switch is in the ON position. It has the
same functions as aileron dual rate.
Power switch
The upper position is ON.
Level meter
This level meter indicates the transmitter battery voltage.
Neck strap bracket
Bracket for the neck strap (optional).
Antenna
Strong telescoping antenna.
Extend
it
to
its full length
when using the transmitter.
Handle
Use this bar to carry the transmitter.
Nonslip adjustable lever head
The length of the lever head can be adjusted to fit the
operator.
Adjust to the length of your hand.
in the arrow direction, and adjust the head to
the most comfortable length, then lock it by
turning it in the direction opposite the arrows.
Battery cover
Remove this cover
when switching the
servo reversing
switches.
and
Unlock lever heads
. by turning them
Lever head
Lever head
Remove the
battery
cover, by
pulling it in
the arrow
direction while
pressing
downward.
Fig.
5
Servo reversing switches
Fig.
4
Using the servo reversing switches
The left side of each switch is the normal position.
•The
servo
reversing
switches
reverse
the direction
of
opera-
tion of the servos.
Fig.
6
Elevator servo
reversing switch
Aileron servo
reversing switch
Throttle servo
reversing switch
Rudder servo
reversing switch
Landing
gear servo
reversing
switch.
NORM - Normal
REV - Reverse
After linkage is complete, inspect the servos. If the direction of
operation of the stick lever and the direction of operation of a
servo are opposite, switch the appropriate servo reversing switch.
Transmitter NiCad battery NT-8LP
Charging jack
Battery charge jack for built-in NiCad battery.
•CHARGING OF
TRANSMITTER
AND RECEIVER
NI-CAD BATTERIES:
Recharge the receiver and
transmitter NiCad
batteries
as shown in Fig. 7.
AC-117V
Battery
Charger
Type
FBC-8B(4)
Rx:
Notes:
1) First, connect to TX NiCad
and red lamp goes on.
2)
Then connect to RX NiCad
after connecting, L, E, D,
changes color trom red to
greenish red (orange)
which indicates that
both TX and RX NiCads
are being charged.
3) In case of separate
charging
L, E, D, color will be:
RX NiCad - Green.
TX NiCad - Red.
•Connect the charging plug of the FBC-8B charge to the
transmitter charging jack, connect the 3P connector of the
FBC-8B to the receiver NiCad battery (NR-4J), and plug the
FBC-8B to a 117VAC outlet as shown in this figure.
•The
Receiver
battery
can
be
used
about 10 times at 10
minutes per flight between rechargings.
Charge the batteries for about 15 hours. When the set is
not
in use for some time, repeat discharge and charge two
to
three times before use. (If the batteries
are not used for a
long time, their capacity will go down).
FBC-8B charges transmitter and receiver NiCad batteries
independently or simultaneously.
The tension of the stick lever spring can be adjusted.
Fig.
8
Tx.
Charging
plug
Fig.
7
(NR-4J)
LED
When adjusting the aileron,
and elevator the inside
module is removed.
Use a small Phillips
screwdriver.
Elevator
Aileron
Rudder
The tension of the
spring can be adjusted
by removing the trans-
mitter back cover and
turning the screw for
each stick. Set the
springs for the best
stick feel.
When these screws are
removed, the back cover
can be removed.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba FP5NLK bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba FP5NLK in de taal/talen: Engels als bijlage per email.

De handleiding is 1,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info