708667
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
5
1 32
4
ON
7
6 8
ECE
Hole
Jack Socket
Terminal Block
Switch Jumper
Upper Keyhold
Fixing Hole
+ve Terminal
(Red Lead)
Link P51
External Tamper
Lower Fixing
(Blue Lead)
-ve Terminal
Link P1
Power Supply
Reset Jumper
+ve Terminal
(Blue Lead)
(Black Lead)
-ve Terminal
Fixing Hole
Upper Keyhole
Preparing and installing our new ELRO 10 Zone alarm system.
We advise to do the pre work, easily on the table, and install later. First unpack all accessories and
sort the batteries together with the accessories. Unscrew and open all products.
House Code:
All products must be programmed with the same house code. In all accessories (not in the Alarm
panel) you will find a code dipswitch block like in figure:
The Alarm Panel:
LCD Display Window
Keypad Status LEDs
Connect battery leads to both back-up batteries: Battery 1 (left): Red lead to +, Blue lead to , Battery 2
(right): Blue lead to +, Black lead to ve battery terminal.
If the telephone based functionality is to be used then the Control Panel will need connecting to a
convenient telephone point. Route the cable from the Power Supply Unit up behind, connect the plug to
the DC power socket in the panel. Take care that during installation and testing on the table, the
sabotage switch and the back stays free. Now set the Alarm panel in programming mode, by pressing:
1 USER SETUPis displayed.
Remote Control:
The Remote Control is used to Arm, Part-Arm 1-2 and Disarm the system, or give a panic alarm.
Insert the 3V (CR2032) battery.
Check if you entered the wished
house code into the remote, same
as in the magnet and the PIR.
We start learning the code to the
Alarm Panel
Use the and buttons to scroll through the menu until 2. SYSTEM SETUP is displayed.
Press and ‘2-1 Learn House Code will be displayed. Press again to set the Control Panel to
receive the House code, press the on the remote control: house code will be displayed in figures.
Testing the Alarm Panel by the Remote Control:
Press: to put the system in the TEST mode.
Create your own personal code, by putting some switches to on,
or off. Be sure that you use the same code in all accessories.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-AP5500---Pro-Alarm-System

Zoeken resetten

  • alarm memory lampje brand en piept, hoe kan ik dit oplossen?? Gesteld op 16-4-2024 om 17:14

    Reageer op deze vraag Misbruik melden
  • Het betreft de Elro AP5500, het alarm memory lichtje blijft knipperen en het apparaat geeft regelmatig een piep toon, Het apparaat al gereset , via de sleutel, code, rondje en kruisje. Dan verdwijnt het ongeveer 5 minuten en het begint daarna weer te knipperen enz,. Wat is de oplossing? Gesteld op 29-1-2022 om 11:27

    Reageer op deze vraag Misbruik melden
  • Op mijn installatie knippert regelmatig het Led Status lampje. Weet iemand hoe ik dit uit kan zetten of wat dit betekent?. Het systeem functioneert overigens prima. Gesteld op 17-12-2021 om 16:11

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro AP5500 - Pro Alarm System bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro AP5500 - Pro Alarm System in de taal/talen: Engels als bijlage per email.

De handleiding is 1,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Snelstart handleiding - Nederlands - 8 pagina's

Elro AP5500 - Pro Alarm System Gebruiksaanwijzing - Nederlands - 42 pagina's

Elro AP5500 - Pro Alarm System Snelstart handleiding - Deutsch - 10 pagina's

Elro AP5500 - Pro Alarm System Gebruiksaanwijzing - English - 49 pagina's

Elro AP5500 - Pro Alarm System Snelstart handleiding - Français - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info