606689
1
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Operating Manual
Shutter module
LLUUXXOORR 440088 SS
408 0 100 (basic device)
LLUUXXOORR 440099 SS
409 0 100 (upgrade module)
11..00 DDeessiiggnnaatteedd uussee
22..00.. SSaaffeettyy nnootteess
LUXOR 408 S
LUXOR 409 S
The LUXOR shutter module controls shutters, awnings and blinds. It expands the
existing LUXOR range and is suitable for installation in houses, flats and offices
etc. The device should be properly installed in a control or distribution box.
Set the final position of the motors before starting up shutter module.
This prevents damaging the covering.
Keep the area of the system’s direction of travel clear.
Disconnect the system/covering from the power supply before carrying out
work on system/coverings.
The direction of travel must be visible during operation if the system is con-
trolled by the device.
Do not connect inputs in parallel.
309 442
DDaannggeerr ooff ddeeaatthh tthhrroouugghh eelleeccttrriicc sshhoocckk oorr ffiirree!!
Installation should only be carried out by a professional
electrician!
WWAARRNNIINNGG
P
S
S
P
Schirm
Schirm
33..00 CCoonnnneeccttiioonn aanndd iinnssttaallllaattiioonn
Do not route the COM line parallel to 230 V lines.
Can be extended to max. 16 devices inc. basic module.
Ensure correct polarity!
If the COM connection fails, the SET LED flashes continuously.
Use the following lines: EIB/KNX bus line type YCYM or Y(ST)Y or
telecommunication line J-Y(ST)Y
Connect both sides of the shielding to the minus bus terminal on the COM bus.
The COM line may be up to 100 m in length.
Always route the COM line separately from other lines
(separate cable).
P
S
S
P
DOWN push
button
UP push button
Diode module
907 0 367;
Can be instal-
led in any
direction!
IInnssttaallllaattiioonn ooff bbuuss lliinnee
LUXOR 400 + LUXOR 408 S
IInnssttaallllaattiioonn ooff iinnppuuttss
Do not connect inputs in parallel!
You can achieve the same effect through configuration (see 9.0 Group
functions/Assigning multiple outputs to one input).
Only connect one motor per channel!
If more than one drive is connected per channel, they must be decoupled via
relay controls.
Push button connection for group G1
(G3 on LUXOR 409 S):
Control voltage 230 V~
Push button connection for group
(G2 on LUXOR 409 S):
Control voltage 230 V~
Push button inputs I 1 to I 4
Control voltage 230 V~
Operating voltage 230 V~
+10 %/ -15 %.
Ensure correct polarity of
LL
and
NN..
IInnppuutt tteerrmmiinnaallss
SS
SS
With push button inputs
II
1 to
II
4, the push button connection for group G1 and
the push button connection for group applies: It is possible to connect diffe-
rent outer conductors/phases (full wave = UP, half-wave = DOWN).
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Theben LUXOR 409 S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Theben LUXOR 409 S in de taal/talen: Engels als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Theben LUXOR 409 S

Theben LUXOR 409 S Gebruiksaanwijzing - Nederlands - 6 pagina's

Theben LUXOR 409 S Gebruiksaanwijzing - Deutsch - 28 pagina's

Theben LUXOR 409 S Gebruiksaanwijzing - Deutsch - 6 pagina's

Theben LUXOR 409 S Gebruiksaanwijzing - Français - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info