620557
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
CE1B3074en / 28.07.2003 Subject to alteration Siemens Building Technologies / HVAC Products
Operating Instructions
RDX…
RDX... – the temperature controller that allows you to easily set the room temperature you want. You have
2 choices. You can either rely on the factory settings or make adjustments that suit your individual needs.
Settings and operation
Warmer / cooler
adjustment of
temperature setpoints
3074Z01en
Buttons for setpoint
adjustments
Fan operating mode selector
Automatic or Continuous On
Operating mode
selector
Heating,
OFF or
Cooling
Display
Normal operation
Energy saving mode
Display of current
room temperature
(in Celsius / Fahrenheit),
or new setpoint
Heating ON
Fan output is switched On
Cooling On
Display of actual
room temperature
Heating and auxiliary heating On
Are your rooms too warm or too cold?
Normal operation
/
The + / - buttons allow you to increase or decrease the current room temperature setpoint in steps of 0.5 °C.
To do this, proceed as follows:
Press
or once
The setpoint display starts flashing
Press the buttons again to change the room temperature setpoint
10 seconds after the last press, the new temperature setpoint will automatically be stored. The display stops
flashing.
Changing from heating to cooling mode
/OFF/
AUX
With the manual changeover, modes can be
selected from heating mode, Off to cooling mode.
Off = not in operation.
Display shows that the heating output is active
Display shows that the heating and auxiliary heating
outputs are both active
Display shows that the cooling output is active
Changing the fan operating mode from Automatic
to Continuous On
Auto
Fan On
The fan output is switched on when the heating or
cooling output is activated
The fan output is switched on permanently
Changing from normal operation to energy
saving mode
/
Changeover from normal operation to energy saving
mode takes place automatically via an external
contact
(window switch / remote operation switch, etc.).
(Function inactive if the Heat-Off- Cool switch is in
the Off position)
Display shows normal operation.
Display shows energy saving mode.
Energy saving mode
If you want to change the factory-set temperature
setpoints (16 °C for heating and 28 °C for cooling),
follow the procedure given below (“Changing the
control parameters”).
Important:
The setpoint of energy saving mode can be
set to Off.
This means that the controller is not active in energy
saving mode and the parameter display shows Off.
Risk of frost!
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens RDX42 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens RDX42 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Siemens RDX42

Siemens RDX42 Gebruiksaanwijzing - Nederlands - 2 pagina's

Siemens RDX42 Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens RDX42 Gebruiksaanwijzing - Français - 2 pagina's

Siemens RDX42 Installatiehandleiding - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info