566737
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
ADAGIO SET – Cordless doorbel set UK - 1
PAC-312 / PAC-314 / PAC-316 / PAC-318
Thank you for purchasing this Profile product. Please
note: It is important that you read this manual before
using the product. And be sure to save this manual for
possible use later.
The cordless doorbell consists of 2 separate
components:
1. Push-button unit (transmitter)
2. Bell unit (receiver)
These items are completely independent of each other
and require no wiring.
When the push-button is pressed in, a signal is sent to
the bell, whereupon the bell is activated. Since it has a
range of up to 100 meters (in open spaces) you can use
the bell virtually anywhere in the house, workshop,
office, set it up in the garden or just carry it with you.
Battery installation
Push-button unit
1. The push-button unit works using 1 x 3v
(CR2032) lithium battery (included).
2. The lithium battery is already installed. Open
the push-button and remove the insulator
strip.
3. Snap the rear side back into position, and the
push-button is ready for use.
To replace the battery:
1. Open up the push-button unit.
2. Remove the metal plate using a screwdriver.
3. Place a 3v battery (CR2032) in the battery
compartment, making sure the positive
terminal (+) is uppermost.
Bell unit
1. Slide the rear cover open.
2. Place 2 AA alkaline batteries into the battery
compartment.
3. The bell unit will produce a two-tone signal,
indicating that it is ready to read a digital code
(see channel selection).
4. Slide the cover firmly back into place; the bell
is now ready for use.
Installation
Push-button unit
Use the two small holes on the
rear of the push-button to mark
the position for securing in
place. Drill small holes and
mount the push-button in
position with screws (self-
tapping 3 x 16mm, included) or
use the double-sided adhesive
tape (included).
Important: If you secure the
push-button onto a metal
upper surface or PVC type of
door (with metal), its maximum range of transmission
will be greatly reduced.
Bell unit
This bell can be used as a portable device - or fixed into
position. On the reverse side, there are two suspension
slots, with which the bell can be hung up using a screw,
and can easily be taken down again. Drill a small hole
and fix a rawlplug in place. Mount the hook (included)
onto the wall using a screw. The bell unit can hung up
safely in this way.
Choice of bell tone
The bell-tone selector button is inside the push-button
unit, below letter “S”. Press the button once to hear the
bell tone already set. Press again to hear and select the
next tune.
1. Long Westminster chime 2. Ding-Dong
3. Telephone ring 4. Circus theme
5. Banjo on my knee 6. Twinkle-twinkle
7. It’s a small world 8. Barking dog
Optionally: It is possible to install an extra push-button
by your back door. By applying the procedure given
above, each push-button can produce a different tune.
Channel selection
The unit is supplied with a pre-set radio frequency. If by
chance the bell should sound for no apparent reason,
it's possible that another device nearby is using the same
frequency. To get round this problem, you can change
the frequency of the push-button and bell.
1. remove the cover behind the push-button.
2. To program or change: remove the batteries
from the bell unit for at least 30 seconds to
prime the memory.
3. place the batteries back into position within.
Press the push-button after the two-tone signal
sound (with a second press of the button if
need be) to confirm the new code. Do this
within 1 minute. Don’t use any other cordless
products for the next 5 minutes.
4. Test for correct operation.
Volume selection
There is a volume-selector button inside the bell unit.
Slide the button to ‘high’ (85 dB) or ‘low’ (82 dB) to set
at the desired bell volume.
Trouble-shooting and tips
Problem: Bell rings, but LEDs fail to light up
Possible cause: - The bell is out-of-range (max.
100m in open spaces)
Possible solution: - Move the bell within range
- Reprogram the channel (see
channel selection)
Problem: Bell does not ring, nor do the LEDs
light up
Possible cause: - Push-button battery is flat
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Profile PAC-318 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Profile PAC-318 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Profile PAC-318

Profile PAC-318 Gebruiksaanwijzing - Nederlands - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info