492763
20
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
COMPLIANCE WITH THE FCC RULES AND
REGULATIONS
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and radiates radio frequency
energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try and correct the interference
by one or more of the following measures:
* Reorient or relocate the receiver antenna
* Increase the separation between the equipment
and the receiver
* Connect the equipment into an outlet that is different from
that to which the receiver is connected
* Consult the dealer or an experienced radio/television
technician for help
The user is cautioned that changes and modifications made to the
equipment without the approval of the manufacturer could void
the user’s authority to operate his equipment.
FCC Authorization Label
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
FCC ID #:
Home Producer 8:
MG3N868629
Command Center: MG3-15-1925R
The Command Center also includes an additional IR
signal extension cord for use with a component that
is not in direct line-of-sight of the Command Center.
If you have a component that is not in the line-of-
sight of the Command Center:
1 Plug the 4 ft. IR signal extension cord into
the back of the Command Center.
2 Run the IR signal extension cord to the
component that is not in the line-of-sight of
the Command Center.
3 Using the supplied double-sided tape, attach
the IR signal extension cord so that the LED
is over or next to the IR sensor of your home
theater component.
4 Test the
Home Producer 8.
The Command
Center will convert the RF signal from the
Home Producer 8
into and IR signal and
transmit that signal to your component
through the IR signal extension cord.
NOTE: If the IR signal extension cord does not
control the component that is not in the line-of-sight
of the Command Center, reposition the LED until the
component is able to be controlled, then re-attach
the LED.
LED
SPECIFICATIONS
Remote Power ..................................................... 4 AAA Batteries
RF Command Console Power ................................. 120 Volts AC
Remote to RF Command Console Range .... 100 Feet (30.48m)
RF Command Console to Device Range .... 25 Feet (7.62m) ±30˚
Remote Dimensions (HWD)........................ 9 3/8 x 2 7/8 x 1 3/8
RF Command Console
Dimensions (HWD) ............................ 1 9/16 x 5 1//16 x 4 inches
Remote Weight (without Batteries) ............................ 8 oz. (220g)
RF Command Console Weight ............................... 10.4 oz (300g)
Specifications are typical: individual units might vary.
Specifications are subject to change and improvement without
notice.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw One for All URC 8090 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van One for All URC 8090 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info