710804
36
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
Troubleshooting Chart
The following table lists symptoms, possible causes, and possible solutions for problems
that might occur.
Table 6. Troubleshooting chart
Possible SolutionPossible CauseSymptom
Check the power cable connections at the
switch and the power source.
Make sure that all cables are used correctly
and comply with the Ethernet specifications.
Power is not supplied to the switch.Power LED is off.
Make sure that the switch is connected to the
Internet and that you discover and add the
switch to your network by using the NETGEAR
Insight app.
The switch is not connected to the
Internet or is not yet discovered and
activated through the NETGEAR
Insight app.
Cloud Connection LED is off.
Check the crimp on the connectors and make
sure that the plug is properly inserted and
locked into the port at both the switch and
the connecting device.
Make sure that all cables are used correctly
and comply with the Ethernet specifications.
Check for a defective port, cable, or module
by testing them in an alternate environment
where all products are functioning.
Port connection is not working.A combined speed and
activity LED or an individual
speed LED and an individual
activity LED are off when the
port is connected to a device.
Break the loop by making sure that only one
path exists from any networked device to any
other networked device. After you connect
to the local browser interface, you can
configure the Spanning Tree Protocol (STP)
to prevent network loops.
One possible cause is that a
broadcast storm occurred and that
a network loop (redundant path)
was created.
File transfer is slow or
performance is degraded.
Verify that the cabling is correct.
Make sure that all connectors are securely
positioned in the required ports. It is possible
that equipment was accidentally
disconnected.
One or more devices are not
properly connected, or cabling
does not meet Ethernet guidelines.
A segment or device is not
recognized as part of the
network.
Break the loop by making sure that only one
path exists from any networked device to any
other networked device. After you connect
to the local browser interface, you can
configure the Spanning Tree Protocol (STP)
to prevent network loops.
A network loop (redundant path)
was created.
A combined speed and
activity LED or an individual
speed LED and an individual
activity LED are blinking
continuously on all
connected ports and the
network is disabled.
Hardware Installation Guide36Troubleshooting
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports
36

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Netgear GC110P bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Netgear GC110P in de taal/talen: Engels als bijlage per email.

De handleiding is 1,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Netgear GC110P

Netgear GC110P Installatiehandleiding - English - 2 pagina's

Netgear GC110P Gebruiksaanwijzing - English - 416 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info