593861
1
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
CHARACTERISTICS
1. Time/calendar display:
Hour, minutes, seconds, month, date and day
of the week.
Fully automatic calendar: Calendar ad-
justs automatically for odd and even months
including February of leap years from the
year 1994 up to the end of 2043.
Time indication: Changeover between 12-
and 24-hour indications is possible.
2. Stopwatch: Measures up to 10 hours with
1100-second readout.
8 lap memory: Up to 8 lap times can be
stored in memory.
3. Stroke function:
The stroke per minute, for example pulse
rate, can be calculated and displayed.
4. Countdown timer:
Preset timer: Nine different lengths of time
(3, 5, 10, 15, 20, 30, 35, 40 and 45 minutes)
have been preset for the timer.
Adjustable timer: Up to 9 hours and 59
minutes can be set in minutes.
Auto repeat function: After the set time is
up, the timer counts down the set time again
as many times as necessary.
5. Daily alarm: The alarm can be set to ring on
a 24-hour basis. At a designated time, the dis-
play is illuminated as the alarm rings.
Hourly time signal: Can be set to ring
every hour on the hour with a single beep.
6. Illuminating light: The light evenly illumi-
nates the display in the dark.
BUTTONS AND DISPLAYS
A
C
D
“A”(AM)/
“P”(PM)
mark
Display marks
Hourly time
signal mark
Seconds
Day
E
Alarm mark
Minutes
Hour
[Cal. W620]
Month
Date
Graphic display
A
C
D
“A”(AM)/
“P”(PM)
mark
Display marks
Hourly time
signal mark
Seconds
Day
E
Alarm mark
Minutes
Hour
[Cal. W240]
Month
Date
B
B
The selection of the display can be made in the
following order with each depression of button
“A”.
Time/calendar
display
Stopwatch
display
Stroke
display
A
A
Timer
display
Alarm display
A
AA
* If the stopwatch is not reset to “00” and button
“A” is depressed to change the mode from the
stopwatch, the timer display will appear, skipping
the stroke display.
* When the display is changed by depressing button
“A”, a confirmation sound beeps.
* A flashing display mark indicates that the corresponding
function is in use.
HOW TO SET THE TIME/CALENDAR
A
C
D
“A”(AM)/
“P”(PM)
mark
Display marks
Hourly time
signal mark
Seconds
Day
B
Date
Month
Minutes
Hour
1. Depress button “A” to show the time/calendar
display.
2. Depress button “B” for 2 to 3 seconds to show
the time/calendar setting display. The second
digits start flashing.
3. Selection of the digits to be adjusted (flashing)
is made in the following order by depressing
button “C”.
Seconds Minutes Date
Hour→→
12- or 24-hour
indication
Month
Year
4. Depress button “D” to set the flashing digits.
One digit is advanced with each depression of
button “D”. Digits except seconds move quickly
by keeping button “D” depressed.
5. After all the adjustments are completed, de-
press button “B” to return to the time/calen-
dar display.
Seconds setting
Depress button “D” in accordance with a time
signal. The seconds are reset to “00” and start
immediately.
When the seconds count any number from “30” to
“59” and button “D” is depressed, one minute is
added and the seconds are reset to “00”.
Notes:
1. When setting the hour digits in the 12-hour
indication, check that “A”(AM)/“P”(PM) mark
is properly set. In the 24-hour indication, there
is no indication.
2. Once the year, month and date have been set,
the day of the week is set automatically.
3. If the watch is left untouched in the time/
calendar setting display with the digits flashing,
it will automatically return to the time/calendar
display in 2 to 3 minutes.
HOW TO USE THE STOPWATCH
The stopwatch can measure up to 9 hours, 59
minutes, 59 seconds and 99 in 1100 seconds.
* Even if the stopwatch display is changed to
another while the measurement is in prog-
ress, it continues counting properly. After
the stopwatch is used, however, be sure to
reset it as the battery energy is consumed
enormously to shorten the battery life.
* While the stopwatch is measuring, the graphic
display turns on and off repeatedly.
A
BC
D
Hour
Minutes
Stopwatch
display mark
Seconds
Current
time
1/100 second
Accumulated elapsed time measurement
C
C
C
Restart
StopStart
Reset D Stop
C
** Accumulate repeatedly by depressing button
“C”.
Depress button “A” to show the stopwatch display.
Stopwatch operation
**
Lap time measurement
C
D
Lap 1 D
C
**
“Lap time” refers to an elapsed time required to
cover a given section of the whole distance.
Lap 2Start
D
StopReset
* Lap time measured and lap number remain
displayed for 10 seconds, and then the mea-
surement in progress and the current time
appear.
* After the measurement is stopped by depressing
button “C”, the current time and total time
will be displayed in the upper and lower rows,
respectively, in 10 seconds.
** Can repeat by depressing button “D”.
Notes:
1. The lap number counts up to “99”. After “99”,
the number is displayed in two digits such as
“00” for 100, “01” for 101, and so on.
2. Up to 8 lap times can be stored in memory. If
more than 8 lap times are measured, the measurements
over 8 will not be stored in memory.
Lap No.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lorus W240 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lorus W240 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info