511243
87
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
79
14 CONNECTING PERIPHERAL EQUIPMENT
DX PACKETCLUSTER TUNE
If you have a TM-D700 transceiver, you can connect the TM-D700 to the TS-480 transceiver to use the DX
PacketCluster Tune function. Connect the 2 transceivers with a cross-wired RS-232C cable as shown below.
Configure the TM-D700 transceiver to the DX PacketCluster node frequency.
TS-480 transceiver
TM-D700 transceiver
Cross-wired cable
RESET
GPS
COM
DATA
MIC
PANEL
PADDLE
KEY
E
X
T.S
P
D
AT
A
RE
M
O
TE
C
O
M
M
IC
P
AN
EL
1 Press [MENU/ F.LOCK] and turn the MULTI control to select Menu No. 56 on the TS-480 transceiver.
2 Press [ ]/ [ ] to select the same communication baud rate configured on the TM-D700 transceiver.
3 Tune to the DX PacketCluster node frequency on the TM-D700 transceiver.
4 Press [F] (1 s), [TNC] on the TM-D700 transceiver.
“TNC APRS” appears on the TM-D700 transceiver.
5 Press [F] (1 s), [DX] on the TM-D700 transceiver.
6 Select a desired DX station data with [
cc
cc
c]/ [
dd
dd
d] on the TM-D700 transceiver.
7 Press [MHz] on the TM-D700 transceiver to transfer the frequency data to the TS-480 transceiver.
If the transferred frequency data is available on the TS-480 transceiver, the frequency data will be
overwritten to the current operating frequency. Otherwise, the operating frequency of the TS-480
transceiver remains unchanged.
For more detailed operation on the DX PacketCluster operation of the TM-D700 transceiver, refer to page 6 of the
TM-D700 instruction manual (Specialized Communications).
Note:
The firmware of the TM-D700 transceiver must be version G2.0 or later to use the DX PacketCluster Tune function.
CROSSBAND REPEATER
If you have a TM-D700 transceiver, you can connect the TM-D700 transceiver to the TS-480 transceiver to use
the Crossband repeater function. Connect the 2 transceivers with a mini DIN cable (6-pin) as shown below.
TS-480 transceiver
TM-D700 transceiver
RESET
GPS
COM
DATA
MIC
PANEL
PADDLE
KEY
EX
T.S
P
D
ATA
R
E
M
O
TE
C
O
M
MIC
PANE L
After connecting the 2 transceivers with the cable, access Menu No. 57 (DTS polarity) on the TS-480 transceiver
and select “on”. You will further need to adjust the audio input/ output level of the TS-480 transceiver using Menu
Nos. 46 and 47.
To DATA connector
To DATA connector
TS-480
ANI
ANG
DTS
NC
ANO
SQC
PKD
DE
PKS
PR9
PR1
SQC
Mini DIN
6-pin male
Mini DIN
6-pin male
Mini DIN
6-pin male
q
w
e
r
t
y
TM-D700
q
w
e
r
t
y
qw
ty
er
87

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-480SAT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-480SAT in de taal/talen: Engels als bijlage per email.

De handleiding is 6,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kenwood TS-480SAT

Kenwood TS-480SAT Gebruiksaanwijzing - Nederlands - 104 pagina's

Kenwood TS-480SAT Gebruiksaanwijzing - Deutsch - 104 pagina's

Kenwood TS-480SAT Gebruiksaanwijzing - Français - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info