554876
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
JS-25 COMBO PIR & glass break detector - 1 - MGD51303
JS-25 „COMBO“ P.I.R. & glass break detector
The JS-25 COMBO is an outstanding “two in one” detector, which
dramatically simplifies alarm installations.. This detector combines two
sensors (P.I.R. motion & acoustic glass break) in one housing. It provides
three independent outputs (P.I.R. alarm, glass break alarm and tamper).
The signal from the P.I.R. sensor is electronically analyzed. This ensures
that the detector provides excellent sensitivity and at the same time false
alarms are basically eliminated. The detection analysis rate can be adjusted
to increase its immunity if the JS-25 is installed in a problematic location. The
standard lens in the detector can be replaced with an optional corridor or pet
immune lens.
The dual technology glass break detector analyses air pressure changes
and sounds to detect the breaking of a glass window. The signal processing
guarantees a high sensitivity to the breaking of all types of glass. The
sensitivity can be adjusted to match various window sizes and mounting
distances. A memory feature enables the user to determine, visually, which
detector triggered the alarm.
For testing, the JS-25 is equipped with two LED indicators (red confirms
a P.I.R. alarm, green confirms a glass breaking alarm).
The COMBO distinguishes itself as a unique 2 in 1 solution with excellent
RF immunity.
Installation
The detector is designed for indoor applications. It can be mounted on a
flat wall or in a corner. Do not place the detector close to any heating/cooling
vents or near any other object that often changes temperature. Do not place
the detector close to any apparatuses that can generate air pressure
changes, low frequency noise or vibrations. The unit must have an
unobstructed view of the protected area and glass.
1. Open the cover of the detector (press in the plastic tab on the bottom
with a screwdriver).
2. Disconnect the cable connecting the front cover with the main PCB.
3. Remove the main PCB by pressing the flexible tab.
4. Punch through the pre-formed holes for cables and screws.
5. Attach the housing to the wall (2.5 meters above the floor).
6. Return the PCB into the housing and connect wires to the terminals.
7. Re-connect the cable and attach the cover.
Note: Avoid touching the P.I.R. sensor!
Terminals
+12V, GND power supply
PIR, PIR P.I.R. alarm output (normally closed)
TMP, TMP TAMPER output (normally closed)
GBS, GBS glass break alarm output (normally closed)
Jumpers
LED the red PIR indicator can be disabled by opening this jumper
DETECTION removing this jumper enables a higher rate of analysis and
increases the immunity of the PIR detector. This setting is
suitable for problematic locations with temperature changes or
electromagnetic interference.
MEM/TEST sets the green LED glass break indicator. In the TEST position,
this LED indicates air pressure changes by a quick flash and an
alarm triggering by a long flash. In the MEM position the LED
indicates a broken glass alarm memory. When the jumper is
disconnected, the green LED is disabled.
PIR detector testing
After switching on the power wait for 1 minute. During this period the
detector initializes and stabilizes its parameters (red LED will be on if not
disabled).
Each detected movement will be indicated by the detector’s red indicator (if
not disabled).
Check if the detector covers the protected area as you expected.
Glass break detector testing and adjustments
Set the MEM/TEST jumper to the TEST position (green LED will indicate
the triggering).
Strike carefully the glass with a cushioned instrument.
Attention, do not break the glass!
The green LED will flash shortly after a strike, if the air pressure sensor
sensitivity is suitably set. The sensitivity can be adjusted using the variable
resistor. Do not adjust too an excessively high sensitivity.
For complete testing of the detector it is recommended to use the GBT-212
glass break simulator. The green LED will light for 2 seconds if glass
breaking is detected.
glass break detector working range diagram
Notes for the glass break detector operation
The memory function can be used to determine the source of an alarm in
the system. If several detectors are used in one zone, you can set the
MEM/TEST jumper into the MEM position. Then, if this detector triggers an
alarm, the green LED will remain on until the MEM/TEST jumper is
disconnected. The detector operates as usual even while the alarm memory is
indicated.
If there is any automatic device in the protected area which can generate
a loud noise (air conditioning, heating or cooling systems etc.), ensure that
this noise does not trigger the glass break sensor. If it does, it is necessary to
relocate the detector or assure that these devices will not be on when the
security system is armed.
A glass break detector located at the entrance can trigger a false alarm
when the door is opened (air pressure change combined with keys clinking on
the glass or a door’s squeaking can simulate the sound of glass breaking). It is
recommended to connect the glass break detector into the delay zone of a
control panel.
PIR detector lenses
Sandard lens that is supplied with the JS-20 Largo detector covers
an area of 120 degrees / 12 meters. See the diagram on the right.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JS-25 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JS-25 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info