554800
1
Verklein
Vergroot
Pagina terug
1/1
Pagina verder
JA-80W wireless combined PIR + MW detector 1 MLI51101
JA-80W wireless combined PIR + MW detector
The JA-80W is a component of Jablotron’s Oasis alarm system. It is
designed to detect human body movement inside buildings. A high immunity to
false alarms is reached thanks to the combination of PIR and microwave (MW)
detection. The PIR part, if triggered, starts the MW detection to confirm PIR
activation. Only then is the triggering transmitted.
Installation
Installation shall only be undertaken by technicians holding a certificate
issued by an authorized distributor. There should be no obstacles blocking the
detector’s “view” of the protected area. Keep the detector away from metal
objects which could interfere with radio communication and the MW field.
8
Description: 1. DIP-switch; 2. MW part connector; 3.PCB tab; 4. tamper-switch; 5.
PIR sensor; 6. front cover tab; 7. MW sensitivity setting; 8. MW detector
1. Open the detector cover by pressing the tab (6) and remove the PCB
which is held by an internal tab (3) Avoid touching the internal PIR
element or damaging the antenna.
2. Punch screw holes through the rear plastic cover according to the
installation point, either for a corner or for a flat wall At least one screw
should penetrate the tamper-sensitive section.
3. Screw the rear cover to the wall, about 2.5 meters above the floor
(vertically, with the tab down).
4. Return the PCB to its original place till the tab (3) clicks..
5. Leave the battery disconnected and the cover open and then follow the
control panel or receiver manual. The basics of enrollment are:
Enter enrollment mode on the control panel by keying in “1” in
Service mode.
Install a battery into the detector to activate enrollment.
Exit enrollment mode by pressing “#”
6. Close the detector cover till the tab clicks. The supplied screw can secure
the tab.
7. After installing a battery into the detector, allow three minutes for
stabilization. During this period the LED is continuously lit.
Notes:
To enroll a detector after having already connected a battery, first disconnect
the battery, and press and release the tamper switch to discharge any
remaining charge to get the device ready for enrollment.
The detector can also be enrolled by entering the serial number – the last
eights numbers of the barcode, which is placed inside the detector.
To follow the EN 50131-2-4 the tab must be secured by the supplied screw.
DIP switch Setting
Switch no.1: DEL / INS: OFF (DEL) provides entrance & exit delays for
detectors installed in a building entrance route. The ON (INS) allows the
detector to instantly trigger alarm activation if the control panel is armed.
DIP switch no.1 only has an effect if the detector has a natural reaction
assigned to it in the OASiS control panel. It also has no effect when used with
a UC-8x or AC-8x receiver.
Switch no.2: PIR NORM / HIGH: selection of immunity to false alarms.
The OFF (NORM) position combines very good immunity with fast sensor
reactions. The ON (HIGH) position gives increased immunity with a slower
reaction time and is only used for problematic installations.
Switch no.3: MW NORM / HIGH sets the time period after PIR detection in
which the MW detection is active. The position OFF – 1 s, ON – 2 s
Switch no.4: MW NORM / TEST. The position OFF is for the standard function
of the detector. The MW detection is triggered by the PIR detection part for one or
two seconds according to switch no.3. The position ON - MW detection works
continuously for testing purposes (walk test).
Testing the detector
15 minutes after closing the detector cover, the LED indicators show detector
activation. A short flash of the red light indicates PIR detection and a long flash
(2 sec) indicates MW confirmation of the movement.
For the proper functioning of the detector, it is essential to set the MW
detection field according to the place which should be monitored. For setting
up, switch the fourth DIP switch to the TEST position. Sensitivity (monitoring
range) can be adjusted by a potentiometer on the MW detection part located
inside the front cover of the detector. Turning clockwise increases the
sensitivity (range). Avoid selecting too high a sensitivity as the detection can
cover e.g. nearby rooms. Generally the MW detection field should be the same
as the PIR detection one. After setting up, switch the DIP switch back to
NORM position.
To save battery energy, the PIR detector switches to battery-save mode 15
minutes after the cover is closed. During battery-save mode the PIR sensor still
always watches out for movement. The first movement detected and consecutively
confirmed by the MW part is then signaled to the control panel instantly, and for the
next 5 minutes the PIR sensor ignores any further movement. After these 5
minutes, the PIR sensor then returns to watching out for movement until re-
triggered.
Battery replacement
The detector regularly checks its battery conditions. If battery voltage is
too low, then the report is sent to the control panel to inform the user or
installer. The detector continues to work and each detected movement is
confirmed by a brief LED flash. The battery should be replaced within two
weeks by a qualified technician in SERVICE mode.
After battery replacement, test the functioning of the detector. Expired
batteries should not be thrown into the garbage, but disposed of according
to local regulations.
Removing the detector from the system
If a detector is removed, the control panel reports the removal. The detector
has to be deleted from its address in the control panel before intentional
removal.
Detection characteristics
Technical parameters
Power supply: Lithium battery type LS(T)14500 (3.6V / 2,4 Ah AA)
Typical battery lifetime: approx. 2 years (DIP switch 3: NORM)
Communication band: 868 MHz, Oasis Protocol
Communication range: approx. 300m (open area)
Recommended installation height: 2.0 to 2.5 m above floor level
PIR detection angle/detection range: 110° / 12 m (with basic lens)
MW detection range / frequency 0.5 to 20 m / 9.35 GHz
Operational environment according to EN 50131-1 II. indoor general
Operational temperature range -10 to +40 °C
EN 50131-1, EN 50131-2-4, EN 50131-5-3 classification: grade 2
Dimensions, weight 110 x 60 x 55 mm, 140 g
Complies with ETSI EN 300220, ETSI EN 300 440-1, EN 50130-4, EN 55022, EN 60950-1
Can be operated according to ERC REC 70-03
Operation requires notification national telecommunication offices of Finland, France, Italy,
Serbia and Montenegro, Spain, Sweden, UK
JABLOTRON ALARMS a.s. hereby declares that the
JA-80W is in compliance with the essential requirements
and other relevant provisions of Directive 99/5/EC. The
original of the conformity assessment can be found at
www.jablotron.com, Technical Support section
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80W in de taal/talen: Engels als bijlage per email.

De handleiding is 0,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info