555056
1
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
The JA-80V LAN / PSTN line communicator - 1 - MKA51202
The JA-80V LAN / PSTN line communicator
The communicator is a component of the Jablotron Oasis 80 system. It
is designed to be installed within the control panel housing. This
manual is valid for firmware version XA64005.
When connected to a PSTN telephone line and LAN (Ethernet) data
network it allows the following:
event reporting by SMS (to up to 8 telephone numbers)
event reporting by phone call with an acoustic warning
event reporting to an ARC (Automatic Receiving Centre – also
known as a Central Monitoring Station) - up to 2 ARCs
remote control and programming by phone (remotely authorizing a
phone keypad or by SMS instructions)
the remote control of appliances in a house by dialling in from an
authorized number (free of charge with unanswered calls)
remote control and programming via the Internet (www.GSMlink.cz
)
The communicator can also be connected only to a telephone line or
only to a LAN network. In these cases it will provide the following
functions:
tel. line only: remote control by phone, event reporting by SMS
and by phone calls and event reporting to ARC2 (CID protocol)
LAN only: remote access via the Internet, event reporting to
ARC1 (IP CID protocol)
1. Installation in the control panel
If you purchased the communicator module separately, it should first
be installed in the Oasis control panel as follows:
a) The control panel power must be switched off (both mains and
battery)
b) Fit the communicator inside the control panel housing using
screws and connect its digital bus RJ cable to the main board
c) Connect the PSTN telephone line cable – the telephone line
should support CLIP protocol (EN 300 089 V3.1.1) with Caller ID
recognition and SMS transfer in text format activated (contact your
phone line provider for more details).
J
A
-
8
0
V
K
A
x
x
x
x
x
x
M
A
C
:
x
x
-
x
x
-
x
x
-
x
x
-
x
x
-
x
x
Ethernet - LAN
cable
Phone
line
Label with
codes
Ethernet status LED
ARC data status
A
RC communication fault
OASi
S
control panel
bus
JA-80V
Fig. 1 Communicator wiring
2. Powering up the communicator for the
first time
If the communicator is installed in the control panel then:
a) Have the LAN (Ethernet) cable ready
b) Switch on the control panel power (mains and battery). The
communicator’s green LED should turn on = no events to send to
the ARC.
c) If your LAN network does not provide an automatic DHCP,
program the Ethernet network parameters manually (see 5.18).
d) connect the LAN cable (10/100 Mbit). If communication with the
network is correct the yellow LED will be constantly lit.
If it starts flashing, check the DHCP parameters, if it turns off (after
3 sec. of flashing) then the communicator is not connected to the
Ethernet at all.
e) If communication to an ARC is desired, then all ARC parameters
have to be programmed according to the ARC provider’s
specifications.
f) Key in 98101 - to set texts of the communicator to English
language.
g) Close the control panel cover
3. User functions of the communicator
The following text describes all communicator features. The installer
should show the end user how to operate the functions used in a
particular installation.
3.1. Temporarily authorizing a phone keypad to be a system
keypad
It is possible to operate the system remotely by temporarily authorizing
a phone keypad as follows:
a) dial the system’s phone number
b) after 25 seconds of ringing (programmable) the system will answer
with a short beep
c) key in a valid access code on the telephone keypad (e.g. 8080 or
1234 if factory default settings are still valid)
d) the phone keypad will behave as a system keypad and an acoustic
signal in the receiver will indicate the control panel status: 1 beep =
SET, 2 beeps = UNSET, 3 beeps = Service mode, 4 beeps = incorrect
code entry, siren sound = alarm
e) now the system can be operated from the phone keypad the same
way as from the system keypad – including the commands starting with
(for example 81 to turn the PGX output on)
f) to exit this mode simply end the phone call (if nothing is entered
within a minute, the phone call will end automatically anyway)
Notes:
do not enter sequences on the phone too fast, each key signal
needs a certain time to be sent
a fixed-line phone can also be used to operate the system
remotely the same way (the phone must use tone dialling)
Phone keypads have to be re-authorized each time the system is
called by entering the codes specified earlier, as phone keypads are
only authorized as system keypads for the duration of a call to the
system.
3.2. SMS instructions to control the system remotely
The telephone line connected to the communicator is used to receive
SMSes but has to support CLIP protocol for SMS transfer in text form
for this feature to work. The SMS transfer parameters should also be
programmed – see 5.11 and 5.12.
All incoming SMSes are checked by the communicator and if there are
any instructions to the system, they will be performed. Each instruction
message must have the following format:
code instruction
(valid code space instruction)
Valid code = any valid code in the system (e.g. 8080, 1234 etc.)
The factory-default instruction texts (editable – see 5.4)
Instruction Function Notes
SET setting (arming)
UNSET unsetting
(disarming)
setting or unsetting (the same way as
if the code used is entered on the
system keypad), If the system is
already in the desired mode, it will not
change
STATUS status
interrogation
including ARC communication (shown
as MS1 and MS2)
MEMORY last event
interrogation
The last event recorded in the control
panel memory
PGX ON turns on PGX
PGX OFF turns off PGX
PGY ON turns on PGY
PGY OFF turns off PGY
the PG output has to be programmed
for the function: on/off (by 237/247) or
2 second switching (by 238/248)
Example: by sending: “code SET” (valid code space SET) the system
will set (if it is already set it will not change its status)
Notes:
performance of the instruction is confirmed by an SMS reply
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80V in de taal/talen: Engels als bijlage per email.

De handleiding is 0,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-80V

Jablotron JA-80V Gebruiksaanwijzing - Nederlands - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info