554804
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
The JA-80PB wireless motion/glass-break detector MHP52504 2
Detection characteristics of the PIR sensor
The default lens supplied covers an angle of 120° and a distance of 12
metres. The area is covered by three beams as shown in the following
picture.
Top view
Side view
The characteristics can be changed by using optional lenses:
JS-7904
Suitable for long corridors. The middle beam covers 20
meters.
JS-7906
Only employs an upper beam with a 120° angle and a 12
metre range. Ignoring the floor eliminates the effect of the
movement of small pets.
JS-7901
Has a vertical beam forming a wall-like detection barrier
which triggers the detector if someone walks through it.
Note: After changing the lens, test that the desired area is protected.
Incorrect installation of the lens can disable detection.
5 minute/1 minute PIR sensor sleep time
To save battery energy, the PIR sensor part of the detector switches to
battery-save mode 15 minutes after the cover is closed. During battery-
save mode the PIR sensor still always watches out for movement. The first
movement detected is then signalled to the control panel instantly, and for
the next 5 minutes the PIR sensor ignores any further movement.
After these 5 minutes, the PIR sensor then returns to watching out for
movement until re-triggered. The sleep time can be shortened to 1 minute
by pressing the tamper switch during battery installation. Not pressing the
tamper switch gives a sleep time of 5 minutes. This sleep time has no
effect on the glass-break sensor which is always ready to trigger a
glass-break alarm.
Auxiliary alarm input
There is an input terminal in the
detector which, among other
things, can be used to detect open
doors or windows. Open circuiting
the input has the same effect as
movement in front of the detector
The maximum allowable cable
length to connect a normally-
closed sensor to the terminal is 3
metres. Short circuit these
terminals if the input is not used.
Detection characteristics of the glass-break sensor
The directional response of the glass-break sensor has near spherical
characteristic and it is possible to detect breaking glass up to 9 metres
away as can be seen in the below diagram. The size of glass should be at
least 60 by 60 cm. For smaller sizes the detection range can be shorter.
Only breaking glass forming part of the walls within the protected area can
be detected. All kinds of glass can be protected including windows covered
with unbreakable folio.
Warning: This type of detector is not suited to sensing holes being cut
through glass by glass cutters. For this reason, valuables near
windows should be covered by PIR sensors.
Glass-break detector relative directional sensitivity
Battery replacement
This detector has two batteries inside whose condition is regularly
checked. If any of the batteries has expired, then the user or installer is
informed. The detector continues to work and each movement in front
of the detector is shown by a brief LED flash. The batteries should be
replaced within two weeks by a qualified technician in SERVICE mode.
After battery replacement the detector needs two minutes to stabilise
during which the LED is permanently lit. After battery replacement test
the functioning of both sensors. Expired batteries should not be thrown
into the garbage, but disposed of according to local regulations.
Removing the detector from the system
If a detector is removed, the control panel announces the removal. The
detector has to be deleted from its two addresses in the control panel
before intentional removal.
Technical parameters
Voltage of PIR sensor: Lithium battery type LS(T)14500 (3.6V AA / 2.4Ah)
Voltage of GBS sensor: Lithium battery type LS(T)14250 (3.6V ½ AA / 1.2Ah)
Typical battery lifetime approx. 3 years (PIR sensor sleep time 5 min.)
Communication band: 868 MHz, Oasis protocol
Communication range: approx. 300m (open area)
Recommended installation height: 2 - 2.5 m above floor level
PIR sensor detection angle/detection range: 120° / 12 m (with basic lens)
Glass-break detection range 9m (glass min. 60 x 60cm)
Operational environment according to EN 50131-1 II. Indoor general
Operational temperature range -10 to +40 °C
EN 50131-1, EN 50131-2-2, EN 50131-5-3 classification: grade 2
Dimensions, weight 110 x 60 x 55 mm, 120 g
Complies with ETSI EN 300220, EN 50130-4, EN 55022, EN 60950-1
Can be operated according to ERC REC 70-03
FCC ID VL6JA80PB
JABLOTRON ALARMS a.s. hereby declares that the JA-80PB is in
compliance with the essential requirements and other relevant provisions of
Directive 99/5/EC and complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void
the user´s authority to operate the equipment. The original of the conformity
assessment can be found at www.jablotron.com
, Technical Support section
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer
after use.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80PB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80PB in de taal/talen: Engels als bijlage per email.

De handleiding is 0,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info