554902
1
Verklein
Vergroot
Pagina terug
1/1
Pagina verder
The JA-63E wired keypad 2 / 2 MKP51001
The JA-63E digital bus wired keypad
The JA-63E keypad is designed to control and program alarm systems of
Jablotron’s JA-6x series. The keypad is equipped with backlit keys, built-in LED
signalling, acoustic signalling, and a display. It conveys information about the
system status in a convenient way. The keypad communicates via the control
panel digital bus. You can connect the keypad to the control panel via an RJ
cable or via a standard communication cable connected to terminals. Multiple
JA-63E keypads can be connected to a single control panel.
Any undesirable mishandling of the keypad (like opening its housing or tea-
ring the keypad off its position) will trigger tamper signalling. In addition, the
number of attempts to enter an access code is checked not to exceed a given
limit.
Installation
Select the desired keypad location close to the building’s entrance.
1. Open the keypad’s rear housing (by pressing the two tabs on the left or
right side).
2. Route all required cables through the hole in the rear housing and install
the housing to the desired location.
3. Connect the digital bus cable either to the terminal board or to an RJ
connector.
4. Close the keypad’s housing (attach the front housing on one side and
push it on the other side).
5. Switching on the control panel power makes the keypad ready for op-
eration.
Tabs
Tabs
SYSTEM 6 0
Installation notes:
Multiple JA-63E keypads in the system must be wired in parallel. Inlet
cables can be split directly in the control panel, in a converter, in the keypad or
in a junction box. RJ cable connection and connection to terminals can be
used in combination.
A connecting cable must be wired so that the corresponding positions
(terminals) are connected. When you use a self-made RJ cable, be careful to
connect identically coloured wire ends to identically marked positions (termi-
nals).
If the keypad does not function after being connected, disconnect the
inlet cable and check if the corresponding positions (terminals) in the control
panel and the keypad are connected.
Operation
The keypad can operate and program the system to the full extent as it is
described in the control panel manual.
The following table describes the meaning of symbols on the keypad LED
indicators:
Alarm
Power supply
Tamper
Set (Armed)
Fault
Battery
Wireless communication indication
Functions F1 through F0 can be used as described in the control panel ma-
nual. Besides this, there are 4 extra keys with the following functions:
Setting (Arm-
ing)
(equal to F1
entry)
Door opening
(equal to F3 entry)
Partial setting
(equal to F2
entry)
Panic (access under
duress)
(equal to F7, before
access code entry)
Remote system access
The JA-63E keypad allows you to remotely operate or program a JA-6x
system via a phone line using a JA-60U modem. Such operation requires the
system to be equipped with a telephone communicator with the remote access
feature enabled (see the security system installation manual).
Note: Remote system access via the JA-63E keypad is only possible using a
JA-60U modem of DY62012 version or higher.
Connecting remotely to the system: Connect the JA-60U modem to the
phone line. Connect the JA-63E keypad cable to the modem’s data connector.
After powering up the modem, the keypad will show a u on the display to
indicate that it is ready to establish a connection.
The initial connection is established by keying in:
xxxxxxxx F1 y F2 ttt...t F3 nnn...n F d
where:
xxxxxxxx is an 8-digit access code for system remote access
y answering machine bypass (a so-called second call) 0-
not bypassed, 1-bypassed
ttt...t call back tel. number – if call back is not requested just
enter F3 after F2
nnn...n the remote system tel. number (a pause can be specified
by keying in F0)
d dialling method: 4-tone, 5-pulse
After the d parameter is entered, the modem will establish a connection
and the keypad will display the remote system status. The keypad then beha-
ves the same way as if it had been connected directly to the system. Depen-
ding on the quality, the telephone line might be slower in its response. A JA-
63 remote connection disables the 4 big keys on the keypad’s right side. Use
keys F0 to F9 instead.
The connection is terminated by pressing key .
A re-connection (using the same modem) is established by entering F6. The
connection parameters are memorized.
If you perform a call to a control panel which has the same access code
but a different telephone number, you do not need to re-enter the whole con-
necting sequence. Instead, it is sufficient to key in nnn...n F4 – i.e. the control
panel tel. number followed by one of the F4/F5 keys (depending on the
tone/pulse dialling method).
Technical specifications
Connection with a cable to the JA-6x digital bus connector
Connecting cable 4 core cable with RJ connectors (4/4 1:1) or
ordinary telephone cable (terminals)
Length of the inlet cable max. 100 m when a paired cable is used
Power supply 10 –14 V (taken from the digital bus)
Power consumption 25mA
Enclosure IP40
Dimensions 125 x 145 x 30 mm
Complies with EN 50131-1, EN 50131-3 grade 2
Environmental class II indoor general -10 to +40°C
EMC EN 50130-4,EN 55022
Contents of the kit: JA-63E keypad, 4 m of connecting cable,
4 rawl plugs, 4 screws, 2 RJ-44 connectors.
Accessories – for keypad connection (can be ordered separately):
RJ-40 converter from RJ connector to 4 terminals
RJ-21 RJ connector splitter (2/1)
RJ-44 cable connector (4P/4C)
RJ-00 crimping tool for RJ connectors
CT-04 cable for RJ connectors
JABLOTRON ALARMS a.s hereby declares that the JA-63E is in compliance
with the essential requirements and other relevant provisions of Directive
2004/108/EC. The original of the conformity assessment can be found at
www.jablotron.com
, Technical Support section.
Note: Although this product does not
contain any harmful materials we
suggest you return the product to the
dealer or directly to the producer after
use. See www.jablotron.com for details.

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-63E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-63E in de taal/talen: Engels als bijlage per email.

De handleiding is 0,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info