458152
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
REQUIRED TOOLS
Hammer, Masking tape, Screwdriver, Drill and 3/16" drill bit (if not
installed on a junction box)
RF ADDRESS CODE SETTING
If there is another user nearby, e.g. in the next house, your
receiver may be fault triggered by their transmitter. You may
select a different RF address code to prevent this. Receiver can
only response to RF coding with the same address code setting as
its own address code.
1.To adjust address code of Receiver, simply push up one or more
of the 5 dip switchlevers.
2.To adjust address code of Control Centre, open the housing of
the transmitter unit. See battery replacement section on how to
open the housing.
3.Remove one or more of the jumper caps as shown in the
diagram below.
CAUTION:
1.Address code of Control Centre must be the same as address
code of Receiver. For any jumper cap removal of address code #
in Control Centre, the same address code # ofReceiver must be
put to the UP position.
2.Disconnect AC power and remove batteries prior to adjusting address code.
WARNING:
After removing the wall plate, if you find that it is mounted on a junction box (e.g. a box
similar to one behind a light switch or electric outlet), high voltage circuit may be present
and there is a danger of electric shock. Please consult a qualified electrician.
CHOOSING A LOCATION
Note: for a new installation, choose a mounting location about five feet (1.5 metre) above
the floor in an area with good air circulation and away from.
1. Drafts.
2. Air ducts.
3. Radiant heat from the sun or appliances.
4. Concealed pipes and chimneys.
MOUNTING THE RECEIVER ONTO THE WALL/JUNCTION BOX:
1.Remove the front cover of the Receiver. (go to step 4 if installed on a junction box)
2.Mark the holes position.
3.Drill two holes and insert the plastic anchors carefully into the holes until they are flush
with the wall.
4.Connect the wires - see wiring diagram.
5.Push on the wires in the wall.
6.Securely fasten the Receiver to the wall with the two screws.
7.Replace the front cover and installation is completed.
MOUNTING THE RECEIVER ONTO THE OPTIONAL WALL BOX:
1.Remove the front cover of the Receiver.
2.Mark the holes position for the wall box.
3.Drill two holes and insert the plastic anchors carefully into the holes until they are flush
with the wall.
4.Pull the wires into the wall box and fasten the wall box onto the wall.
5.Connect the wires - see wiring diagram.
6.Push on the wires in the wall box.
7.Securely fasten the Receiver to the wall box with the two screws.
8.Replace the front cover and installation is completed.
WIRING DIAGRAM FOR 230V
APPLICATION
The unit is default 230V, you must
ad a link between COM & L, follow
diagram.
WIRING DIAGRAM FOR VOLT
FREE APPLICATION
The unit still requires a 230V feed
for V.F. applications
4. SETTING OF CONTROL CENTRE
Heater/Cooler Selection
Before making any selection in the control centre, its back housing must be removed as
follows:
Inside the Control Centre after back housing is removed, you can find the DIP switch. These
three switches are used to control the span and heat/cool system. Set the DIP switch
(position 3) according to your selection of heater system or cooler system as the following
diagram.
NCNC
NN
LL
COMCOM
NONO
SL (Off) - Heat Off
L - Live
SL (On) - Heat On
N - Nuetral
It is vital to connect the
live into this terminal to
avoid overloading of the
jump wire.
NCNC
NN
LL
COMCOM
NONO
N - Nuetral
L - Live (230V Feed)
NO - Switched Live
COM - Volt Free Feed
NC - Normally Closed
Most common connexion
in Europe.
swtich 3 ON = heaterswtich 3 ON = heater
swtich 3 OFF = coolerswtich 3 OFF = cooler
-3- -4-
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro KT 300RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro KT 300RF in de taal/talen: Engels als bijlage per email.

De handleiding is 0,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elro KT 300RF

Elro KT 300RF Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Espanôl, Polski, Türkiye - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info