701137
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
1.
Instant Heat ON/OFF key
2.
Adjustment Up key
3.
Disengaged pre-set symbol
4.
Ventilation symbol
5.
Temperature ramp.
6.
Current Time, Preset Time,
Heating Time, Run Time
and Diagnostics.
7.
Day selected indicator boxes.
8.
Clock symbol.
9.
Heater operation symbol.
10.
Preset Programme
symbols.
11.
Adjustment Down key.
12.
Programme key.
13.
Set/Programme key.
8
9
10
11
12
13
7
6
5
4
3
2
1
Low Heat
High Heat
701 Series Timer / Modulator With Diagnostic Readout Instructions
Introduction
Your Timer/Modulator offers manual
and programmable control along with
temperature adjustment of your heater.
When the heater is switched on by the
Timer/Modulator in a programmed
mode it will run for 1 hour or for the
duration time that you have selected e.g
Heater on at 0700, duration time of 1 hour,
which means heater will be switched off
automatically at 0800.
C
lock Settings:-
Press and hold
key until the
symbol
begins to flash. Use the
begins to flash. Use the
and
keys to
set correct time. Press and release the
key and the day box will begin to flash.
Use the
and
keys to set the correct
day. Press and release the
key again to
reset the clock to the start of the minute
displayed. This may be used to coincide
with a known time signal.
Please Note:
These adjustments are not possible
when the heater is in operation. To set the
heater’s programmable switch on timer, see
“Setting Program Times”.
S
witching on the Heater
(Manually)
Press the
key and the
symbol will
appear on the display. The heater will
commence its startup cycle. The display
will change to show a default of one hour
heating countdown time. This can be
extended
in increments of 10 minutes,
30 minutes, 1 hour, 1 hour 30 minutes, 2
hours
up to eight hours or to continuous
up to eight hours or to continuous
running operation (shown as C-: -- on
display) by repeatedly pressing the
key
while the heater is in operation. Current
time will be displayed every 5 seconds.
Switching off the Heater
(Manually)
The heater may be switched off at any time
by pressing the
key. The cooling down
cycle will then be initiated.
Adjusting the Temperature
Pressing the
and
keys will alter the
20 segment temperature ramp shown on
the display. This level may be adjusted
at any time and will remain in the
timer memory when the heater is not in
operation.
Diagnostic Readout
With the heater switched on, press and
hold
key until the display shows
“dAtA”. Release key and display then
shows “AF--” and alternatively displays
the current fault code. Each press of
the
key will scroll through the last 5
previously stored fault codes.
Typical fault codes -
10 = Over voltage - Check battery charging system.
11 = Under voltage - Check battery voltage.
12 = Overheating - Check air ducts for obstruction.
52 = Safety time exceeded - Check fuel supply.
For other codes consult your local dealer.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Eberspacher-Timer-Modulator-701-serie

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eberspacher Timer Modulator 701 serie bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eberspacher Timer Modulator 701 serie in de taal/talen: Engels als bijlage per email.

De handleiding is 0,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info