471920
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Important
Note
Warning
Pay attention to the road or trail! Do not be distracted by the
computer.
•Be sure to securely mount the magnet, the sensor, and the
bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws are not loosen.
Keep batteries out of reach of small children. Dispose of batter-
ies according to local regulations.
Avoid unnecessary prolonged exposure to the sun. Never at-
tempt to disassemble the computer head.
Don’t use thinner, benzene or alcohol to wipe the surface of the
computer. They may damage the surface of computer.
Computer Set-up (For 1st use or after replacing the battery)
All Clear
Push three buttons (MODE, START/
STOP and SET) at the same time.
* Do this procedure without fail for
stable measurement when you use
this system for the first time and every
time the battery is replaced.
1
Starting the odom-
eter from zero.
Retaining the current odometer reading
(the odometer starts from the reading you
inputted)
SET
MODE
MODE
ST/STOP
ST/STOP
Set The Tire Circumference
Set the tire circumference in cm.
Note
You can easily set it by referring to the chart shown
right.
Setting is completed by pushing the SET button.
3
Increase the
number.
Max. 300 cm
Decrease
the number
Min. 100 cm
Preparation Complete.
(the screen will show the time measurement in this state)
* The auto mode is ON in this state.
MODE Button
START/STOP Button
SET Button
!
L(cm)
14 x 1.50 102
14 x 1.75 106
16 x 1.50 119
16 x 1.75 120
18 x 1.50 134
18 x 1.75 135
20 x 1.75 152
20 x 1-3/8 162
22 x 1-3/8 177
22 x 1-1/2 179
24 x 1 175
24 x 3/4Tubular 178
24 x 1-1/8 179
24 x 1-1/4 191
24 x 1.75 189
24 x 2.00 192
24 x 2.125 196
26 x 7/8 192
26 x 1(59) 191
26 x 1(65) 195
26 x 1.25 195
26 x 1-1/8 190
26 x 1-3/8 207
26 x 1-1/2 210
26 x 1.40 200
26 x 1.50 201
26 x 1.75 202
26 x 1.95 205
26 x 2.00 206
26 x 2.10 207
26 x 2.125 207
26 x 2.35 208
26 x 3.00 217
27 x 1 215
27 x 1-1/8 216
27 x 1-1/4 216
27 x 1-3/8 217
650 x 35A 209
650 x 38A 212
650 x 38B 211
700 x 18C 207
700 x 19C 208
700 x 20C 209
700 x 23C 210
700 x 25C 211
700 x 28C 214
700 x 30C 217
700 x 32C 216
700C Tubular 213
700 x 35C 217
700 x 38C 218
700 x 40C 220
L cm
SET
ST/STOP
MODE
Contact Point
Select The Measurement Unit
Select the measurement unit, kilometer
or mile, by pushing the MODE button.
2
MODE
Choose Either of The Followings.
•When you want to input the reading of the currently
used odometer, keep pressing the MODE button for
two seconds and input the reading.
•When you want to start the odometer from zero,
push the START/STOP button.
Kilometer
Mile
SET Button
MODE Button
START/STOP
Button
Input the current reading of odometer.
For two seconds.
Increase the
number.
Move the
decimal point.
You need to know the tire
circumference (L cm) be-
forehand.
Tire size
Tire size is usually shown
on the sidewall of tires.
®
3
2
1
Installation of the Computer on Your Bike
The computer is combined with the following parts.
1
2
5
3
6
7
4
3
7
Important Note
Mount the sensor 3 at the appropri-
ate position so that the center of the
magnet 5 will align with the
marked line on the sensor when the
wheel is rotated.
Important Note
Rotate the sensor on the front fork to
adjust the gap between the sensor
and the magnet 5 within 5 mm, and
secure it with the nylon ties.
Mount The Bracket
Secure the cord on the front fork with the nylon ties (smaller ones) 7 and coil it around the
brake cable that leads to the handle bar.
Put the rubber pad 6 on the bracket 1 and secure the bracket on the handle bar with the
screw. Slide the computer into the bracket until you hear the click sound
The contact points are automatically closed. When you need to remove the computer, slide
forward the computer with the lever pushed simultaneously.
Note
Allow enough wire clearance in the area marked with an to insure that you can
turn the handlebar from left to right without pulling the wire.
Basic Functions Test
Rotate the front wheel gently and see if the computer indicates the
running speed.
Note
When the computer does not indicate the speed, check
the position of the magnet and the sensor.
4
3
5
1 Bracket
2 Cord
3 Sensor
4 Sensor Rubber Pad
Center
5 Magnet
6 Bracket Rubber Pad
7 Nylon Ties (5)
Front Fork
3
2
1
Please read these instructions carefully before attempting to
install and use your CAT EYE MITY 8 computer so that you
understand the functions of this product.
Please don’t throw away this manual, Keep the manual at a place easily accessible.
5
Spoke
Rotate the front wheel.
OK
7
Front Fork
Sensor Side
Within 5 mm
Marked Line
1
Slide
1
6
Mount sensor and adjust the gap between the
magnet and the sensor.
Secure the sensor 3 with the larger nylon ties 7 at
the appropriate place and in the right direction.
Mount the magnet
5 on a spoke of the front wheel so that the surface
of the magnet will face the sensor.
Lever
MITY8
CAT EYE MITY 8
CYCLOCOMPUTER CC-MT400
E: Owner’s Manual
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending
Copyright © 2002 CAT EYE Co. Ltd.
CCMMT4-021210 066600230 1
You can refer to the guide
chart to roughly know the
tire circumference.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cateye CC-MT400 Mity 8 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cateye CC-MT400 Mity 8 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Cateye CC-MT400 Mity 8

Cateye CC-MT400 Mity 8 Gebruiksaanwijzing - Nederlands - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info