614664
2
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
GB
Notes on Safety
Instructions for installation and connection.
Disconnect the battery ground wire during installation and connection.
This car radio can be used for both 2 x 20 or 4x7watts operation. For
this, the corresponding connector box has to be mounted to the car radio.
When drilling a hole, be sure not to damage any vehicle parts (battery,
cable, fuse case, etc.).
The positive cable must have a cross-section of at least 1 mm. The unit
is protected by a quick-acting fuse of 5 A.
If you use a motor or electronic antenna, it will be activated when the TIM
function is switched on, which will lead to a certain current drain.
Note:
By means of the support included in delivery you can mount the set in cars
with a DIN car radio cut-out of 182 x 53 mm, an installation depth of 165
mm and an instrument panel thickness around the fixing clips of 1 - 20
mm, see fig. 1.
For cars with other cut-out dimensions Blaupunkt delivers car-specific
installation kits for common car types for 50/52 mm sets. Use enclosed
distance plates only for installation kits of 52 mm sets.
Please check the dimensions and, if necessary, use a car-specific
installation kit, e. g. VW Golf II / Jetta II/: 7 608 3824 73.
When using installation sets for units of 52 mm four distance plates, order
number 8 601 055 056 must be used, fig. 1a.
Preparation of car radio installation
Install the car radio into the DIN cut-out provided in your car’s dashboard
ex factory.
Prepare the car radio DIN cut-out (unlock shelf or dummy cover) or cut
out the car radio compartment to 182 x 53 mm.
Grasp behind the car radio cut-out and check how many of the fixing
strips of the car radio support may be bent.
Note:
Try to bend as many fixing strips as possible.
Insert the support into the cut-out and bend the appropriate fixing strips
with a screwdriver, see fig. 1, 2.
Connection
Connection overview .................................................................... fig. 4
Notes on connection ..................................................................... fig. 5
Connection of equalizer and amplifier .......................................... fig. 6
Connection CD-Player .................................................................. fig. 7
Loudspeaker connection:
4 speakers (4 /7 W).................................................................... fig. 9
2 speakers (4 /22 W)................................................................ fig. 10
Depending on the speaker equipment of the respective vehicle either the
2- or 4-channel connector box has to be exchanged (the 2 x 20 watts box
is marked).
Change connecting box
1. Loosen the screw and unlock the top and bottom support springs by
lifting them, see fig. 15.
2. Pull out the connecting box, see fig. 16.
3. Position the connecting box with the sides in the correct position and
parallel to the cabinet, and push it in carefully, see fig. 17.
4. Tighten the screw and hook in the top and the bottom support screw.
5. Replace the fuse of the connecting box.
Important notes!
If these notes are disregarded, there is danger of destroying the
final stages.
Do not connect speaker outputs to ground!
Connection with multiple plug installed ex factory
Audi, VW
Passive loudspeaker system:
Use QuickFit or adapter cable.
Active loudspeaker system:
Pin 1, 2, 3 and 4 of the +/- connector (8 pins, black) shall be disconnected.
Connect the wire at pin 3 to pin 5. Connect the wire at pin 4 to pin 7.
Opel
1. Remove the car radio support prior to the installation. Disconnect the
compact connector and the antenna cable.
2. Check the compact connector. Pin 1, 2 and 3 of chamber 3 (8 pins)
must not be connected.
3. Exchange pin 4 and pin 7 of chamber 3 against each other.
Ground cable
Do not connect the ground cable to the negative pole of the battery.
Route the ground cable to a suitable ground point (car body screw, car
body metal sheet) and shorten it accordingly.
Remove the insulation from the ground cable and attach the forked cable
lug (if necessary, solder it).
Scratch off the paint from the contact area of the ground point and
lubricate it with graphite grease (important for good ground contact).
Screw on the ground cable.
Positive cable (ACC 12 V) (ignition)
Connect the positive cable together with distributor to pin 30 (constant
power) or pin 15 (positive line connected via ignition) of the fuse holder
behind the fuse.
Permanent plus connection (Battery 12 V)
Connect the permanent plus terminal together with the cable and cable
clamp to a fuse-protected positive line (e.g. clock, warning flasher).
Control cable (Power Antenna +)
Connect the antenna’s control cable to the control cable of the car
stereo when installing a fully automatic motor antenna or electronic
window antenna. The switching line must not be used as the switching
voltage for an amplifier, since the control cable can be live even if the
set is off with the TIM function being activated. The amplifier would then
be activated. The control cable is fuse-protected.
Lighting connection (Illumination)
Lighting connection for vehicles with adjustable dashboard lighting (plus-
controlled).
Amplifier
The preamp jack is not occupied. Amplifier connection via loudspeaker
outputs only. To set up the amplifier’s switching voltage, attach the
enclosed cable to chamber 1 of the power supply connection block.
Car radio installation
Insert the car radio from the front into the support and push in until the
stop springs on the sides engage right and left (distinct click to be heard).
Removal of the car radio
Insert the brackets right and left into the provided trimplate holes and
push in until you hear a distinct click (lateral springs are unlocked).
Using both brackets (see fig. 5), pull the unit out.
Note:
Locked brackets can only be removed after taking out the unit.
QuickOut (shuttle support)
Use the car radio specific QuickOut support.
Modifications reserved.
+12V
per. +12V
+12V
Preamp.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt Stockholm RCR42 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt Stockholm RCR42 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds als bijlage per email.

De handleiding is 0,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info