495938
11
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
11
Troubleshooting
Symptom Possible Problem Solution
There is a crackling
sound coming from
the speaker (when
connected to PC
or laptop).
The operating system’s volume level
is set too high.
Check the operating system volume level and
decrease it if necessary.
Interference. Move the unit to another location or select a
different RF channel.
The sound is distorted.
The M812’s volume level is set too
high.
Lower the volume level of the M812 by using the
supplied remote control or the VOLUME – key on
the speaker.
The EQ function is enabled on the
iPod and there is too much bass.
Disable the EQ function of the iPod or turn down
the bass on the M812.
The WALL/TABLE switch on the
bottom of the wireless speaker is in
the wrong position.
Ensure the WALL/TABLE switch on the bottom of
the M812 is set to the proper position.
Intermittent buzzing. The unit is located too close to a
GSM cell phone.
Move the GSM cell phone away from the unit.
The wireless speaker
stops playing or cuts out.
The M812 has gone into an over-
current, protection mode.
Reduce the volume level. The M812 will
automatically reset itself after a short period of
time. When the M812 resets it will come back in
the standby mode. Upon powering the unit back
up reduce the volume level to prevent it from
going into protection mode.
It appears that the
wireless speaker is
not reproducing a
stereo signal.
The MODE switch on the bottom of
the unit is in the wrong position.
Set the MODE switch to the correct position;
STEREO, when one speaker is used. LEFT
or RIGHT when two speakers are used in the
same room.
I have three speakers
connected to one
transmitter base that
lost sync and now it
will not automatically
re-synchronize.
In a multi-speaker system if a single
speaker loses synchronization that
speaker unit will not be able to
automatically regain synchronization.
To manually regain synchronization between the
transmitter base and the speakers, hold down
the STANDBY key on the transmitter base for six
seconds. The speakers will then synchronize with
the transmitter base.
My speaker is picking
up music from a
different source.
Your speaker has synchronized to
another transmitter base that is within
range of your speaker.
You can manually re-synchronize the speaker by
holding down the POWER key on the speaker for
six seconds. The speaker will then synchronize
with the transmitter base.
NO SYNC shows on
speaker display.
Synchronization between speaker
and transmitter base has failed.
Disconnect the speaker power cord from the
wall outlet, wait 30 seconds, reconnect to the
outlet and power on the speaker. Press and hold
the STANDBY key on the transmitter base for
six seconds. If situation persists, you may need
to manually set the RF channel. See Set RF
Channels in Advanced Operations (page 8).
The LCD displays “iPod,”
and the iPod is playing,
but no sound is coming
from the speaker.
The speaker and transmitter base
have a poor connection.
Press and hold the STANDBY key on the
transmitter base for six seconds. This will cause
the speaker to re-synchronize with the transmitter
base.
iPod does not function
properly when docked to
the transmitter base.
You may need to update the software
on the iPod.
Go to the Apple Web site and follow the
directions to upgrade your iPod to the latest
software.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Altec Lansing M812 - Octiv wireless bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Altec Lansing M812 - Octiv wireless in de taal/talen: Engels als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info