Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
Turn the programme selector to the desired programme; the light
of the
“Start (Pause)”
button blinks. The
temperature
and
spin speed
indicated on the display can be altered by pressing the
“Temperature” button or the “Variable spin” button.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Prewash” button
•Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
•Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Clean+” button
•Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
•Choose temperature of 30 or 40°C and use with maximum load.
•Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
•Prolongs the programme by approx. 10 to 15 minutes.
•Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Easy ironing” button
•Makes ironing easier by an increased water quantity and a very
gentle spin.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft water or
for washing baby linen, and helps people with allergies.
“Variable spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
•If you select “Rinse hold” , the laundry remains in the last
rinse water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold”, press the “Variable spin” button repeatedly until the
“Rinse hold” symbol on the display lights up.
-The wash programme stops to “Rinse hold” when the
“Rinse hold” symbol on the display blinks; the light of
“Start (Pause)”
button blinks as well.
-To terminate the “Rinse hold” by draining the water,
without any spinning, press the
“Start (Pause)”
button.
-To terminate the “Rinse hold” by spinning the laundry, press
the “Variable spin” button to select the desired spin speed
and then
“Start (Pause)”
to start the spin cycle.
-Do not leave the laundry to soak for too long in the “Rinse hold”.
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton959.087
**
2.602:20
Coloured Cotton
***
609.0641.532:30
Coloured Cotton409.0820.802:15
Synthetics603.546
**
0.851:35
Synthetics403.5420.501:20
Delicates302.5600.400:45
Wool402.0600.600:45
Handwash402.0450.600:40
Baby407.0950.852:32
Big Items403.0740.751:30
Sport303.5540.551:34
SuperEco609.0801.084:00
Daily load406.0730.601:00
Speed 15303.0300.200:15
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
SAVE YOUR FAVOURITE PROGRAMMES
•Select the desired programme, temperature, spin speed and
option(s), push and hold the
“Favourites”
button for at
least 3 seconds. The lamp next to
“Favourites”
shortly
blinks and then lights up - the programme setting is saved.
Next time you want to use your individual programme setting,
select the programme, push the
“Favourites”
button and
start by pushing
“Start (Pause)”
.
If you want to replace the saved programme setting by another
one, proceed as already described above.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
•Select programme, temperature, spin speed and options.
•Press the Start delay button to select one of the delay time
steps between 0:30 and 23:00 hours.
•Press the
“Start (Pause)”
button .
The countdown of the delay time begins; the clock symbol next to
the delay time and the colon between hours and minutes blink.
•The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
To cancel the “Start delay”
..before you press the “Start (Pause)” button:
•Press the
“Reset / Drain”
button , or set the start delay
time to “0:00” - the delay time disappears after a few seconds.
..after having pressed the “Start (Pause)” button:
Press the
“Reset/Drain”
button for at least 3 seconds; the
start delay time disappears from the display. Or press
“Start
(Pause)”
twice to start the selected programme immediately.
Before starting a programme, the symbol lights to show that the
door can be opened to add more washing. As soon as you press
“Start (Pause)”
, the door will lock until the end of the
programme and must on no account be forced open. In case you
have to open it urgently during a running programme, refer to
“Reset a running programme before the end”.
If you try to start a wash programme and the door is not properly
closed, the “Add garment” indication will blink.
Open the tap and press the
“Start (Pause)”
button; the
blinking
“Start (Pause)”
button light becomes constant. The
“Add garment” indication goes out, and the lit bubbles indicate that
the programme is in process. In some phases, the remaining
programme time is newly calculated - if this is the case, the “6
th
sense” indication on the display will fade, and the remaining
programme time is replaced by an animation.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
•Turn the programme selector to a programme position, or run
a programme as usual.
•Press the “Temperature” and the “Variable spin”
button simultaneously for at least 3 seconds. The “Child lock”
symbol will shortly blink and then light up to indicate
that the child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off by turning the programme selector
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
•The display shows “End”, and the “Programme finished”
indication lights up.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
•Leave the door ajar to allow the drum to dry.
•If you do not turn the programme selector to the “Off / O”
position, all lights of the control panel go out after a few
minutes to save energy - only “End” will remain on the display.
The symbol will blink at the end of the programme if you used too
much detergent. Use less detergent next time.
1.Press the
“Start (Pause)”
button to pause the
programme. The light blinks.
2.Select the new programme, temperature, any options and
another spin speed if you want.
3.Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The
“Reset/Drain”
button cancels a programme before the end.
•Press the
“Reset/Drain”
button for at least 3 seconds; an
animation appears on the display. Any existing water is drained
out before the door can be opened.
START DELAY
“ADD GARMENT” INDICATION
PROGRAMME START
CHILD LOCK
RED FAILURE INDICATIONS
PROGRAMME END
DETERGENT OVERDOSAGE INDICATION
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
The Sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of your wash load.
30106406GB.fm Page 2 Friday, June 18, 2010 4:01 PM
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Whirlpool awoe 9558 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Whirlpool awoe 9558 in de taal/talen: Engels als bijlage per email.
De handleiding is 0,27 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.