459871
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
5019 301 01193
Whirlpool is a registered trademark of Whirlpool USA.
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton/ Antibacterial 95 6.0 59 * 1.90 2:00
Cotton with “Eco” ** 60 6.0 49 0.90 4:00
Cotton 60 6.0 49 1.02 2:20
Cotton 40 6.0 54 0.65 2:00
Synthetics 60 2.5 50 * 0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Lingerie 30 1.0 45 0.50 0:36
CONSUMPTION DATA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data
in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load
and the type of wash.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the
lamp lights to show the the door can be opened.
As long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel (Reset)
a running programme before the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for
Use”; if the fault persists, contact our After Sales
Service.
Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap: if the indications still lights
up, refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned:
in the latter case refer to the Instructions for Use
(“Removing the Filter”).
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause”
button lights up. The programme sequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain.
When the programme phase is finished, the
corresponding indication goes out.
PROGRAMME END
All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before
the end.
Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door
can be opened.
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
Do not use liquid detergent
when activating “Start delay” option.
Select programme, temperature and options.
Press the “Start Delay” button to select the delay
time by 1, 3, 6, 9 or 12 hours.
Press the “Start/Pause” button.
The indication over to the “Start Delay” button
lights up and goes off when the programme
starts.
Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. When
the programme starts, the start delay indicator
light goes off and is replaced by the programme
sequence indication.
After the “Start/Pause” button has been
pressed, the number of hours preselected can be
reduced by pressing again the “Start Delay
button.
To cancel the “Start Delay
..before you press the “Start/Pause” button:
Turn the programme selector to another position
or press the “Reset” button.
..after having pressed the “Start/Pause” button:
Press the “Reset” button for at least 3 seconds -
the start delay indicator light goes out.
START DELAY
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
Close the door and turn the programme selector
to the desired programme and temperature. The
indication lamp next to the “Start/Pause” button
blinks and the indication lamp of the predefined spin
speed lights up.
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of options
are deselected automatically.
“Prewash” button
Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
Do not use liquid detergent for the main wash
when activating the “Prewash” option
.
“Eco” button
With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Inensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
The laundry remains in the last rinse water
without pregressing to the final spin cycle to avoid
creasing and prevent colours from changing.
This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
If you select “Rinse hold” do not leave items to
soak for too long.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” lights in the
preogramme sequence indication is on.
The indication lamp next to the “Start/Pause”
button flashes.
Terminate the “Rinse hold” option:
Press the “Start/Pause” button; the programme
will terminate automatically with the final spin
cycle for the present wash programme.
If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain
programme and press the “Start/Pause” button.
Variable spin” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during the rinse. The water is drained out only.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Whirlpool-AWO-4472

Zoeken resetten

  • Mijn wasmachine AWO 4472 is stilgevallen midden het programma. Er branden geen verklikkers meer, al meet ik stroom in de machine na wegname bovenste klep. Gesteld op 3-2-2020 om 14:11

    Reageer op deze vraag Misbruik melden
  • er brand geen enkel lichtje,, machine start niet op : stroomtoevoer is o.k. Gesteld op 24-7-2017 om 11:48

    Reageer op deze vraag Misbruik melden
    • Ook ik zit met ditzelfde probleem en blijkbaar vele mensen met ons. Is hier eigenlijk al een antwoord op gegeven? Is het de moeite om een technieker te laten komen (€100 voorrijkosten) en dan te horen dat het €200 kost voor reparatie (als dat kan) . Voor €50 meer heb je een nieuwe ??? Geantwoord op 22-10-2017 om 09:55

      Waardeer dit antwoord (14) Misbruik melden
  • Mijn machine heeft 2 dagen geleden een programma zonder problemen afgewerkt. Gisteren wou ik de machine aanzetten maar de wasmachine start niet en er branden geen lampjes. De stekker stak goed in het stopcontact en het wandstopcontact functioneert. Gesteld op 24-11-2015 om 09:42

    Reageer op deze vraag Misbruik melden
    • Beste,
      Ik heb deze week net hetzelfde meegemaakt. Er is geen probleem met het stopcontact. Heeft u ondertussen ondervonden wat het probleem is? Geantwoord op 17-10-2016 om 15:11

      Waardeer dit antwoord (17) Misbruik melden
  • bij het starten van de was gaat de wasverzachter direct mee ,wat kan de oorzaak zijn ? Gesteld op 15-1-2015 om 14:32

    Reageer op deze vraag Misbruik melden
  • Er is een beugel van een beugel-bh door de wasmachinetrommel heen geschoten.
    Hoe kan ik daar nu bijkomen?
    Vr.groet
    E.H.P.C.Driesenaar
    Email:gitaarstudiojobim@gmail.com Gesteld op 2-10-2014 om 13:24

    Reageer op deze vraag Misbruik melden
    • Hallo.
      Die beugels maken nogal wa lawaai hé.
      Gewoon de machine volgens het boekje volledig leeglaten,de beugel opzoeken,met een piellamp, hoofd in de trommel, en de beugel met een fijne schroevendraaier of een breinaald volledig naar beneden brengen tot voor de afvoeropening onderaan in de kuip.
      wasmachine schuin achterover tegen de muur plaatsen en de zwarte afvoerdarm onderaan de kuip losmaken en daar moet je de beugel kunnen uithalen met een lange fijne bektang
      Veel succes.

      Mvg.

      Willy. Geantwoord op 19-11-2014 om 18:17

      Waardeer dit antwoord Misbruik melden
  • De bovenste balk geeft 1h, 3h, 6h, 9h en 12h. Wat houdt dit in? Ik dacht altijd dat het hier om de duur ging, maar een was van 12 uur lijkt me sterk op zo'n apparaat. Ik heb de machine nu een half jaar en wil voor het eerst een flinke hoofdwas van 1 uur laten draaien ipv maar 30min, klopt het nu dat dit niet mogelijk is? Misschien dat iemand ook kan vertellen waar die getallen nu echt voor zijn, want een duidelijke gebruiksaanwijzing zat niet bij het apparaat, terwijl uitleg voor het aansluiten en de eerste was te draaien er in meerdere talen bij zat. Gesteld op 24-3-2014 om 17:50

    Reageer op deze vraag Misbruik melden
    • De uren betekenen dat de wasmachine pas na 3Hr; of na 6 Hr; enz. start met haar wasprogramma,meestal om snachts te wassen (stille uren tarief, of nachttarief op welbepaalde uren)
      Ne flinke hoofdwas is volgens mij een kookwas met bijbehorende voorwas op 90 graden.
      Wat betreft de handleiding voor uw toestel, dit is zeer makkelijk te downloaden van het internet , merk en toesteltypenr.intypen en je ziet wel.

      Mvg.

      Willy.
      Geantwoord op 19-11-2014 om 18:08

      Waardeer dit antwoord (1) Misbruik melden
  • 6
  • mijn machine draait niet meer. Het start een programma op, geen foutmeldingen, je hoort dat hij gaat draaien maar hij doet niks.
    Gesteld op 13-1-2014 om 13:00

    Reageer op deze vraag Misbruik melden
    • beste,

      ik heb dit meegemaakt met mijn vorige wasmachine. de koolborstels waren versleten, die moeten steeds contact hebben met de koperen draadjes vd motor. Koolborstels besteld via Handy Man in Gent. 86€. Indien je handig bent kan dit zelf vervangen. Geantwoord op 30-1-2014 om 21:03

      Waardeer dit antwoord Misbruik melden
  • Om een halfwas te draaien hoe stel ik het progamma in Gesteld op 9-1-2013 om 23:50

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Whirlpool AWO 4472 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Whirlpool AWO 4472 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Whirlpool AWO 4472

Whirlpool AWO 4472 Gebruiksaanwijzing - Nederlands - 11 pagina's

Whirlpool AWO 4472 Snelstart handleiding - Nederlands - 2 pagina's

Whirlpool AWO 4472 Gebruiksaanwijzing - Nederlands - 13 pagina's

Whirlpool AWO 4472 Gebruiksaanwijzing - Deutsch - 14 pagina's

Whirlpool AWO 4472 Snelstart handleiding - Deutsch - 2 pagina's

Whirlpool AWO 4472 Gebruiksaanwijzing - English - 15 pagina's

Whirlpool AWO 4472 Gebruiksaanwijzing - Français - 11 pagina's

Whirlpool AWO 4472 Snelstart handleiding - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info