662522
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
AFTER SALES SERVICE
Before contacting After-Sales Service:
Make sure that you cannot solve the problem yourself
following the points described in chapter
“Troubleshooting Guide“.
If after the above checks the fault persists, contact the
nearest After Sales Service.
Please give:
a brief description of the fault;
the type and exact model of the hob;
the service number (i.e., the number that follows the
word SERVICE on the rating plate, located under the
hob). The service number is also indicated on the
warranty booklet;
•your full address;
your telephone number and area code.
If any repairs are required, please contact an authorised
After Sales Service (to guarantee that original spare parts
will be used and repairs carried out correctly).
Failure to comply with these instructions may
compromise the safety and quality of the product.
INSTALLATION
Recommendations
Important: Disconnect the hob from the mains before
carrying out any installation work or servicing.
All electrical connections must be made before
connecting the appliance to the power supply.
Installation must be carried out by a qualified technician
in accordance with the manufacturer's instructions and
in compliance with local regulations.
Unpack the hob and make sure that the appliance has
not been damaged during transport. If you are not
sure contact the dealer or the nearest service
centre.
Preparing the housing unit
Cut the worktop to fit before installing the appliance.
Carefully remove any shavings or sawdust that could
prevent the appliance from running properly.
The hob must be fitted in a worktop with a minimum
thickness of 30 mm and a maximum of 50 mm.
Insert a separator at least 20 mm from the lower edge
of the hob, so that it cannot be accessed by the user.
If there is an oven under the hob, make sure that it is
manufactured by Whirlpool and equipped with a cooling
system.
There must be nothing between the hob and the oven
(e.g. cables, insulating material, etc.).
An adjacent column unit must be installed at least
100 mm from the edge of the hob.
Cut an opening in the worktop of the given dimensions.
We recommend you seal the internal edges of the
worktop with wood glue or silicone.
If not already in place, apply the supplied seal to the
hob, after cleaning the adhesive surface thoroughly.
Glass ceramic hob
Important: remove any protective film before installing
the hob.
Make sure that the opening in the worktop for the hob is cut
according to the dimensions given in the drawing, paying
attention to the tolerance range.
Assembly
1. Position the clips (A) in the spaces provided on the hob trim (fig. 3) if not already positioned.
2. Measure the centre point of the vertical sides of the cut-out (fig. 1)
3. Fit the brackets (C) in the centre of the vertical sides, aligning the upper edge of the brackets so that they are flush with
the worktop surface (fig. 2).
4. Fix the brackets with the 4 screws supplied (B) using the holes provided.
5. Insert the hob in the cut-out, making sure the clips (A) are secured in the spaces provided (fig. 4).
C
B
fig. 2
fig. 1
For setting into a marble worktop, contact the After-sales Service for the installation kit and necessary
instructions.
4812 310 19277 Installation kit for marble worktop.
Electrical connection
Regulations require that the appliance is earthed.
Connection to the mains must be carried out by a
qualified technician in accordance with the
manufacturer's instructions and in compliance with local
regulations.
The installer is responsible for connecting appliances
correctly to the mains and for observing the safety
regulations.
The power supply cable must be long enough to
connect the built-in appliance to the mains.
Observance of safety directives requires that a multi-
pole switch with a minimum contact gap of 3 mm be
used for the installation.
Do not use multiple plug adapters or extension leads.
After the appliance has been installed, the electrical
components must be inaccessible.
Connecting the hob to the power supply
Note: the yellow/green earth wire must be connected to the
screw marked .
If the supply cable is not already connected:
Strip away approximately 70 mm. of the outer sheath of
the cable.
Then strip away approximately 10 mm. of the inner
sheath.
Open the terminal board by pushing the side clips in
with the help of a tool.
Insert the cable in the cable clamp and connect the
wires to the terminal board.
Close the cover of the terminal board.
After the electrical connection, fit the hob from the top
and hook it to the fixing springs, as shown in fig. 1.
Declaration of conformity
This cooking hob is suitable for contact with foodstuffs
and complies with EEC (CE) Regulation n. 1935/2004.
This cooking hob has been designed to be used only for
cooking. Any other use (such as heating a room) is
improper and dangerous.
This cooking hob has been designed, constructed and
marketed in compliance with:
- safety objectives of the “Low Voltage” Directive
2006/95/CE (which replaces 73/23/CEE and
subsequent amendments);
- protection requirements of EEC “EMC” Directive
2004/108/EC.
A
fig. 4
fig. 3
Fig. 5 Fig. 6
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Whirlpool AKT 360 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Whirlpool AKT 360 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Whirlpool AKT 360

Whirlpool AKT 360 Gebruiksaanwijzing - Nederlands - 2 pagina's

Whirlpool AKT 360 Gebruiksaanwijzing - Deutsch - 2 pagina's

Whirlpool AKT 360 Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info