805519
1
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
Your thermostat has 2 advanced menus.
In order to enter a menu, use joystick , and select
The first menu is meant for the end user.
Keep pushing the
key for 5 seconds.
The second menu is meant for the system installer.
Keep pushing the joystick key for 10 seconds or 5sec after the first menu.
Once you have chosen a menu, go to the parameter which you can change by using .
Use the joystick to modify and confirm by pushing the joystick .
To leave the parameter menu, choose « End » and push .
*Pr
ess
th
e
k
ey
t
o
r
e
l
oad
th
e
pa
r
a
m
e
t
e
r v
a
l
ue
t
o
th
e
f
ac
t
o
r
y
de
f
au
lt v
a
l
ue
.
INSTALLER’S AND USER’S PARAMETERS
Use the joystick to change the mode
Mode BOOST
Press the joystick
to enter in the BOOST mode.
Use the joystick to make blink the duration or the temperature.
When the value is blinking use the joystick to adjust:
- The duration with duration in hours « Hour » when it’s less than 24 h or in days « day ».
- The desired temperature for this duration (adjustable between 5 and 37°C)
To valid your adjustments press the joystick
.
To leave the BOOST mode before the end duration, press the key.
Mode COMFORT
Use this function to set your installation in comfort mode.
Use the joystick to adjust the setting temperature. (Default setting 21°C)
Mode AUTO
Use this mode so that your installation follows the pilot wire orders
When the thermostat receives an order the logo appears.
You can check this order by pressing 2 seconds on the joystick .
The title of the order is displayed during 5 seconds on the left of the display, the temperature
displayed is the new calculated setting temperature.
Orders description:
- 1 => setting temperature – 1°C
- 2 => setting temperature – 2°C
- 4 => setting temperature – 4°C
OFF => the system is shut OFF
A_F => Anti Freeze mode => setting temperature = 7°C
Mode REDUCED
Use this function to set your installation in comfort mode.
Use the joystick to adjust the setting temperature. (Default setting 17°C)
Keyboard lock and unlock function.
Available in all modes.
To lock the key board, maintains the joystick
pressed and press the key at the same
time, then the symbol “ “appears.
To unlock the key board repeat this procedure, (the symbol “ will to disappear)
Error codes
Error on the External (Floor) sensor => Err and are blinks.
Error on the internal sensor => Err and are blinks.
FUNCTION MODES DESCRIPTION
Parameters User’s Menu
numbers names Description of the parameter Works adjustment Other regulations
01 °C °F Select a type “°” on the display °C °F
02 CAL Air
Calibration of the internal probe
(The calibration must be done after 12H working
with the same setting temperature. Check the
room temperature with a thermometer and enter
the reel value)
Air sensor + 0°C From -5°C to +5°C
03 CAL Flor Calibration of the external probe (if connected)
(The calibration must be done same as above) Floor sensor + 0°C From -5°C to +5°C
09 End To exit the user’s menu
The software version is displayed on the bottom FLUS n x.xx
Parameters Installer’s Menu
numbers names Description of the parameter Works adjustment Other regulation
11 SENS Selection of the sensor for regulation « Air Only»
Room sensor only
« Air Lo »
Room sensor with floor limitation
(Low limitation)
« Air Hi »
Room sensor with floor limitation
(Hight limitation)
« Air LoHi »
Room sensor with floor limitation
(Hight and Low limitation)
« Flor Only »
Floor sensor only
12 rEGU Selection of regulation type « bp »
Proportional band « hyst »
Static differential of 0.5°C
13 t Cy Selection of the proportional band duration in
minutes « 10 » Electrical Floor heating « 10 »
Panel Heater « 10 »
14 t on Minimal starting time in minutes « 002 » Adjustable 0 to 5
15 t off Minimal resting time between 2 heating cycles in
minutes « 003 » Adjustable 0 to 5
16 bp Value of the proportional band in °C « 4.0» Adjustable 1°C to 7°C
17 Load Value of the connected load in Watts «1500 »
«500» For Load < 500W
«1000» For 500 < Load < 1000W
«1500» For 1000 < Load < 1500W
«2000» For 1500 < Load < 2000W
«2500» For 2000 < Load < 2500W
«3000» For 2500< Load < 3000W
«3500» For 3000< Load < 3500W
18 FL.Li
Lo
Lower limit of the floor temperature. Only
effective if the external probe is connected and
selected. « 18°C » From 5°C to « FL.Li »
Lo
19 FL.Li
Hi
Upper limit of the floor temperature. Only
effective if the external probe is connected and
selected. « 28°C » From « FL.Li »to 37°C
Hi
20 ALL reset This parameter allows you to choose the works
adjustments Keep pressing during a few seconds
29 End To exit the installer’s menu
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Watts EFHT-LCD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Watts EFHT-LCD in de taal/talen: Engels als bijlage per email.

De handleiding is 0.78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info