620378
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
CE1B3072en / 03.03.2013 Subject to alteration Siemens Building Technologies / HVAC Products
Set the first switch on time
1. Set the programming selector to position A1. The setting for the first switch on
time flashes.
2. Turn the setting knob counterclockwise - to decrease the time, or clockwise + to
increase the time.
3. When the required switch on time is displayed, move the programming selector
to any other position to confirm the setting.
Set the first switch off time
1. Set the programming selector to position A2. The setting for the first switch off
time flashes.
2. Turn the setting knob counterclockwise - to decrease the time, or clockwise + to
increase the time.
3. When the required switch off time is displayed, move the programming selector
to any other position to confirm the setting.
Set the second switch on time
1. Set the programming selector to position A3. The setting for the second switch
on time flashes.
2. Turn the setting knob counterclockwise - to decrease the time, or clockwise + to
increase the time.
3. When the required switch on time is displayed, move the programming selector
to any other position to confirm the setting.
Set the second switch off time
1. Set the programming selector to position A4. The setting for the second switch
off time flashes.
2. Turn the setting knob counterclockwise to decrease the time, or clockwise + to
increase the time.
3. When the required switch off time is displayed, move the programming selector
to any other position to confirm the setting.
Set comfort temperature
1. Set the programming selector to position
.
2. The setting for the current comfort temperature flashes.
3. Turn the setting knob counterclockwise - to decrease the temperature setting, or
clockwise to increase the temperature setting.
4. When the required comfort temperature is displayed, move the programming
selector to any other position to confirm the setting.
Set energy saving temperature
1. Set the programming selector to position
2. The setting for the current energy saving temperature flashes.
3. Turn the setting knob counterclockwise - to decrease the temperature setting,
or clockwise + to increase the temperature setting.
3. When the required energy saving temperature is displayed, move the
programming selector to any other position to confirm the setting.
Note: Set the controller to RUN when all programming is completed.
Temporarily change current setpoint
1. The current programmed temperature can be changed temporarily when the
operating mode selector is in the AUTO position and the programming selector
in the RUN position.
2. Turn the setting knob slightly in either direction to display the current programmed
temperature, turn it counterclockwise to decrease the temperature, or clockwise to
increase the temperature .This new temperature is maintained until the next
switching time. The hand symbol is displayed when activated.
Changing
the batteries
1. Get 2 new alkaline batteries type AA, 1.5 V.
2. Within 1 minute: Remove the battery holder, then the batteries, insert the new
batteries and replace the battery holder. The old, set values must be checked!
3. Properly dispose of old batteries per environmental regulations.
Front View Receiver
LED Signal Indicator
LED Relay Indicator
The signal is good when the
LED is solid green.
A solid red LED indicates that
there is no signal.
Orange LED indicates relay is on.
OVERRIDE Button *
* Note: When press OVERRIDE
the RF data will not affect the
output during 15 min. After 15
min, the output and LED will not
change if not RF receive. If
receive RF, the output and LED
will follow the RF data.
Press this button to manually switch on or
off
RESET : Press the LEARN & OVERRIDE
button for 4 seconds to delete all transmitter
addresses.
LEARN Button
Rear View Room Unit
(Transmitter)
Press the button to put into learn mode
TEST Button
Used for testing transmission.
Mounting plate must be
removed to get access
to the back!
Learn Button
Press to learn telegram
Configuration instructions for the Siemens RDJ10RF/SET
The Transmitter RDJ10RF room unit and the receiver RCR10/433 are set to communicate (bonded) with
each other at the factory. If they fail to do so at installation or it is necessary to re bond the units due to
loss of communication please follow the following instructions.
1. For room unit: Set the programming switch to RUN and the selector switch to AUTO.
2. If room unit is wall mounted remove from wall or if on table stand remove grey backing plate
3. For receiver Reset by simultaneously pressing the LEARN & OVERRIDE button for 4 seconds.
4. On Receiver Press and release the LEARN button. This puts the receiver in learn mode.
5. On room unit Press and release the LEARN button on the back.
6. A green solid LED indicates a good signal, a red solid LED indicates no signal.
7. To test transmission, press the TEST button on the transmitter, this switches the relay to ON on
the receiver regardless of temperature. The RF TEST symbol appears on the display (1 s).
8. An orange LED indicates that the relay is on.
Energy saving tips without sacrificing comfort
Do not allow room temperatures to exceed 21 ºC.
NOTE: You can press the OVERRIDE button on the receiver to manually switch ON/OFF for a faulty
room unit or transmission protocol.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens RDJ10RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens RDJ10RF in de taal/talen: Engels als bijlage per email.

De handleiding is 0,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Siemens RDJ10RF

Siemens RDJ10RF Gebruiksaanwijzing - Deutsch - 2 pagina's

Siemens RDJ10RF Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info