71692
20
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
en
20
Eliminating minor faults yourself
Before you call customer service:
Please check whether you can eliminate the fault yourself based on the following information.
Customer service will charge you for advice – even if the appliance is still under guarantee!
Appliance
Ice maker
Fault Possible cause Remedial action
Appliance has no refrigeration capacity.
The light does not work.
The display does not illuminate.
Appliance has been switched off. Press the On/Off button.
Power failure. Check whether the power is on.
The fuse has been switched off. Check the fuse.
The mains plug has not been inserted properly. Check whether the mains plug is secure.
The refrigeration unit is switching on
more frequently and for longer.
Appliance opened frequently. Do not open the appliance unnecessarily.
The ventilation openings have been covered. Remove obstacles.
Large quantities of fresh food are placed
in the freezer.
Activate “super” cooling and/or “super” freezing.
The light (LED) does not work. The LED lamp is defective. Call customer service.
Light switch is jammed. Check whether it can be moved.
Display indicates “E..”. Electronics have detected a fault. Call customer service.
Display indicates “LOWPOWER”. The mains voltage falls below the permitted
limiting value.
When the mains voltage reaches the stipulated value
again, the warning message goes out. If the warning
message lasts for longer, inform the energy supply
company.
Display indicates “HIGHVOLT”. The mains voltage exceeds the permitted
limiting value.
When the mains voltage reaches the stipulated value
again, the warning message goes out. If the warning
message lasts for longer, inform the energy supply
company.
Condensation forms on the rail on
the left door.
Condensation of warm air. Switch on heater in the rail (see chapter “Special
functions”, section “Door rail heater”).
Fault Possible cause Remedial action
The ice maker doesn’t work. Ice maker is not connected to the mains supply. Call customer service.
Ice maker does not contain any fresh water. Ensure that the water is properly connected.
The freezer compartment temperature is too
warm.
Check freezer compartment temperature and, if
required, set slightly colder.
The ice maker does not make enough
ice or the ice is deformed.
The appliance or ice maker has only just been
switched on.
Approx. 24 hours is needed until ice production starts.
A lot of ice has been taken. Approx. 24 hours is needed until the ice cube container
is filled again.
Low water pressure. Connect the appliance to the stipulated water pressure
only (see chapter “Connecting the appliance”, section
“Water connection”).
The water filter is bunged up or used. Change the water filter.
Temperature in the freezer compartment is too
warm.
Set temperature slightly colder in the freezer
compartment.
Ice cubes have accumulated on the rear panel of
the ice cube container.
Distribute ice cubes in the ice cube container. If ice
cubes are stuck to each other, loosen with a blunt
implement.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Siemens-CI-24-RP-00

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Siemens CI 24 RP 00 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Siemens CI 24 RP 00 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Siemens CI 24 RP 00

Siemens CI 24 RP 00 Gebruiksaanwijzing - Nederlands - 40 pagina's

Siemens CI 24 RP 00 Gebruiksaanwijzing - Deutsch - 22 pagina's

Siemens CI 24 RP 00 Gebruiksaanwijzing - Français - 25 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info