382559
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
POWX033 EN
Copyright © 2015 VARO NV P a g e | 5 www.varo.com
Caution: saw blades can get very hot.
Saw blades must be kept sharp and in good condition. Replace partially fractured and
broken saw blades immediately.
Work calmly and evenly with the jig saw. You will thus avoid accidents and the saw blades
and the jig saw will last longer.
7 OPERATION
7.1 Switching On & Off
7.1.1 Instant response operation (Figure 1)
Switching on: Press the On/Oft switch
Switching off: Release the On/Off switch
7.1.2 Continuous operation
Switching on: Press the On/Off switch, keep pressed and lock with the locking button
Switching off: Press the On/Off switch and release
See Fig 1.
A : Locking button
B : On/Off switch
7.2 Changing the saw blade (Figure 2)
Switch off the jigsaw and remove the plug from the power socket before changing the blade or
carrying out any other work on the jigsaw.
Use the supplied hexagon-socket spanner to undo the two screws on the ram (Figure 2). Slide
the saw blade into the guide slot and up to the stop between the piston rod and the retention
clip. Use the supplied hexagon-socket spanner to tighten the two screws. The teeth of the saw
blade must face in cutting direction. Make sure that the saw blade sits property in the guide
slot of the ram and roller.
Important: Make sure that the saw blade sits properly in the slot of the roller and ram.
See fig 2 (Releasing the saw blade: Turn screw anticlockwise.)
7.3 Electronic speed control setting (Figure 3)
Using the knurled screw on the On/Off switch you can pre-set any speed.
Turn the knurled screw in PLUS direction for a higher speed and turn it in MINUS direction for
a lower speed.
The ideal cutting rate depends on the specific material and working conditions.
The general rules for tool speed in cutting operations apply.
See Fig 3
(1) turn the speed controller to increase the cutting rate.
7.4 Adjusting the base
(for mitering and sawing near edges, Figure 4)
For mitre and bevel cuts you can swivel the base by up to 45° in either direction after undoing
the two screws on the bottom The angles 15°, 30° and 45° are marked but you can adjust the
saw to any angle between these markings as required.
To adjust the cutting angle, undo the two screws (Figure 4) until you can just about move the
blade. Adjust to the required angle and re-tighten the two screws.
To enable you to saw right up to the edge, the base can be pushed backward. To do so, undo
the two screws underneath (Figure 4) and push the base to the back. Re-tighten the two
screws.
See FIG 4
Undo the two screws to set the base to an angle of 0° to 45° on the right or left side.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Powerplus-pow-x033

Zoeken resetten

  • KAN IK HET KLEMSTUK VOOR HET ZAAGBLAD VAST TE ZETTEN KRIJGEN IS IN TWEE GEBROKEN BIJ HET VAST ZETTEN MET EEN INBUSSLEUTEL Gesteld op 2-12-2020 om 10:41

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus pow x033 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus pow x033 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus pow x033

Powerplus pow x033 Gebruiksaanwijzing - Nederlands - 9 pagina's

Powerplus pow x033 Gebruiksaanwijzing - Deutsch - 9 pagina's

Powerplus pow x033 Gebruiksaanwijzing - Français - 10 pagina's

Powerplus pow x033 Aanvulling / aanpassing - Alle talen - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info