50298
5
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
28 5
Programmation
La programmation s’effectue en appuyant sur le bouton de la
fonction désirée. Après avoir relâché ce bouton, il est suffisant de
programmer le temps avec + et - entre 5 secondes.
Boutons + et -
En appuyant sur les boutons + et - le temps augmente ou diminue
à une vitesse variable selon la durée de la pression sur le bouton.
Réglage de l’heure
Pour régler l’heure désirée, appuyer en même temps sur deux
boutons quelconques (durée de cuisson, fin cuisson, compte-
minutes) et + ou -. Par cette opération, tous programmes
précédents sont éliminés, les contacts sont débranchés, et le
symbole AUTO clignote.
Fonctionnement en manuel
En appuyant sur le bouton de manuel, les contacts du relais se
branchent, le symbole AUTO s’éteint, le symbole de casserole
apparaît. Le fonctionnement manuel a lieu seulement à la fin de
la programmation automatique ou après que celle-ci a été éliminée,
s’allume de nouveau quand l’heure correspond au temps de début
de cuisson. Une fois le temps de cuisson écoulé, le symbole AUTO
clignote. La sonnerie retentit et le symbole de durée et le relais
s’éteignent.
Compte-minutes
Appuyer sur le bouton compte-minutes et sélectionner le temps
de cuisson désiré avec le bouton + ou -.
Pendant le fonctionnement du compte-minute le symbole de la
cloche apparaît. À la fin du temps choisi, la sonnerie retentit et le
symbole de la cloche s’éteint.
Signal acoustique
Le signal acoustique se met en marche à la fin d’une programmation
ou de la fonction compte-minutes et il a une durée de 15 minutes.
Pour l’arrêter, appuyer sur un bouton quelconque des fonctions.
Début programme et contrôle
Les programmes démarrent à peu près 4 secondes après leur
programmation.
Il est possible de vérifier à tout moment le programme en cour en
appuyant sur le bouton concerné.
Erreur de programmation
Il y a un erreur de programmation si l’heure indiquée par l’horloge
est comprise entre l’heure de début cuisson et l’heure de fin
cuisson. L’erreur de programmation peut être corrigé, en changeant
la durée ou le temps de fin cuisson. Quand il y a un erreur de
programmation les relais se débranchent.
Élimination d’un programme
On peut éliminer un programme en appuyant sur le bouton de
durée cuisson et puis sur le bouton - afin que l’indication 00 00
GAS CONNECTING
FRGB
A
U
T
O
Minuterie sonore
Durée de cuisson
Fin de cuisson
Manuel
Diminution du temps
Augmentation du temps
apparaisse sur l’affichage lumineux. À la fin d’un programme, ce-
ci s’éliminera automatiquement.
Fonctionnement automatique
En appuyant sur le bouton de durée ou de fin cuisson, le
programmateur se commute automatiquement de la fonction
manuelle à la fonction automatique.
Fonctionnement semi-automatique avec durée de cuisson
Appuyer sur le bouton de durée de cuisson et programmer le
temps désiré avec + ou -. Le symbole AUTO et de durée de cuisson
apparaissent en permanence. Le relais se branche immédiatement.
Quand le temps de fin de cuisson correspond à l’heure, le relais
et le symbole de durée de cuisson se débranchent, la sonnerie
retentit, et le symbole AUTO clignote.
Fonctionnement semi-automatique avec fin de cuisson
Appuyer sur le bouton de fin cuisson. L’heure apparaît sur l’affichage
lumineux. Sélectionner le temps de fin cuisson désiré avec le
bouton +. Les symboles AUTO et durée de cuisson apparaissent
en permanence. Les contacts du relais se débranchent.
Quand le temps de fin cuisson correspond à l’heure, le relais et
le symbole de durée de cuisson se débranchent. Une fois le temps
de cuisson écoulé, le symbole AUTO clignote, la sonnerie retentit,
le symbole de durée de cuisson et le relais s’éteignent.
Fonctionnement automatique avec durée et fin de cuisson
Appuyer sur le bouton de durée et sélectionner la durée de cuisson
désirée avec + ou -. Les symboles AUTO et durée apparaissent
en permanence. Le relais se branche. Appuyer sur le bouton de
fin de cuisson. Le temps de fin cuisson le plus proche apparaît sur
l’affichage lumineux. Sélectionner le temps de fin cuisson désiré
à travers le bouton +.
Le relais et le symbole de durée se débranchent. Le symbole
s’allume de nouveau quand l’heure correspond au temps de début
de cuisson. Une fois le temps de cuisson écoulé, le symbole AUTO
clignote. La sonnerie retentit et le symbole de durée et le relais
s’éteignent.
Compte-minutes
Appuyer sur le bouton compte-minutes et sélectionner le temps
de cuisson désiré avec le bouton + ou -.
Pendant le fonctionnement du compte-minute le symbole de la
cloche apparaît. À la fin du temps choisi, la sonnerie retentit et le
symbole de la cloche s’éteint.
Signal acoustique
Le signal acoustique se met en marche à la fin d’une programmation
ou de la fonction compte-minutes et il a une durée de 15 minutes.
Pour l’arrêter, appuyer sur un bouton quelconque des fonctions.
Début programme et contrôle
Les programmes démarrent à peu près 4 secondes après leur
programmation.
Il est possible de vérifier à tout moment le programme en cour en
appuyant sur le bouton concerné.
Erreur de programmation
Il y a un erreur de programmation si l’heure indiquée par l’horloge
est comprise entre l’heure de début cuisson et l’heure de fin
cuisson. L’erreur de programmation peut être corrigé, en changeant
la durée ou le temps de fin cuisson. Quand il y a un erreur de
programmation les relais se débranchent.
Élimination d’un programme
On peut éliminer un programme en appuyant sur le bouton de
durée cuisson et puis sur le bouton - afin que l’indication 00 00
apparaisse sur l’affichage lumineux. À la fin d’un programme, ce-
ci s’éliminera automatiquement.
ELECTRICAL CONNECTION
This appliance must be installed by a qualified person in
accordance with the latest edition of the IEE Regulations and
in compliance with the manufacturer instructions.
Ensure that the voltage is the same as that stated on the rating
plate. The rating plate can be found on the back cover .
WARNING! THIS APPLIANCE MUST BE EARTHED
The cooker must be connected to a suitable cooker control unit
incorporating a double pole switch having a contact separation
of at least 3mm in all poles, which is adjacent to (but not above),
and not more than1.25m away from the cooker and capable of
electrical isolation.
We recommend that the cooker circuit is rated to 13 amps.
Cable type HO5 RRF 3 X 1.5 mm
2
Connecting the mains cable
Open the mains terminal block cover as shown, unscrew screw
“A” the cable clamp and unscrew (not fully) the screws in the
mains terminal block “L N E” which secure the three wires of the
mains cable. Fit the cable and refit screw “A” the cable clamp.
Allow sufficient cable length for the cooker to be pulled out for
cleaning, but do not let it hang closer than 50mm (2”) to the floor.
The cable can be looped if necessary, but make sure that it is not
kinked or trapped when the cooker is in position.
INLETSTOP
This appliance shall be installed in accordance whit the regulations
in force and only in a well-ventilated space. Read the instructions
before installing or using this appliance.
IMPORTANT
Conversion for use on and other gases must only be undertaken
by a qualified person. For information for use on other gases
contact your local Service Centre.
The cooker must be installed by a qualified person in accordance
with then local rules
Failure to install the appliance correctly could invalidate any
manufacturers warranty and lead to prosecution under the above
quoted regulations.
Provision for Ventilation
The room containing the cooker should have an air supply in
accordance with local rules. The room must have an opening
windows or equivalent; some rooms may also require a permanent
vent. If the room has a volume between 5 and 10m
3
, it will require
an air vent of 50cm
2
effective area unless it has a door which
opens directly to the outside. If the room has a volume of less than
5m
3
, it will require an air vent of 100cm
2
effective area. If there
are other fuel burning appliances in the same room. Ensure that
the room containing the cooker is well ventilated, keep natural
ventilation holes or install a mechanical ventilation device
(mechanical cooker hood). Prolonged intensive use of the appliance
may call for additional ventilation, for example opening of a window,
or more effective ventilation, for example increasing the level of
mechanical ventilation where present. This cooker is not fitted with
a device for discharging the products of combustion. Ensure that
the ventilation rules and regulations are followed. Excess steam
from the oven, vents out at the top back edge of the cooker, so
make sure that the walls behind and near the cooker are resistant
to heat, steam and condensation. Your cooker must stand on a
flat surface so that when it is in position the hob is level. When in
position check that the cooker is level by using a spirit level and
adjust the 2 feet at the rear and the 2 feet at the front if necessary.
It is important that the cooker is stable and level for the overall
cooking performance.
Remember that the quantity of air necessary for combustion must
never be less than 2m
3
/h for each kW of power (see total power
in kW on the appliance data plate).
Gas Safety (Installation & Use) Regulations
It is the law that all gas appliances are installed by competent
persons in accordance with the current edition of the Installation
& Use Regulations. It is in your interest and that of safety to
ensure compliance with the law.
Gas Connection
Prior to installation, ensure that the local distribution conditions
(nature of the gas and gas pressure) and the adjustment conditions
are compatible. The adjustment conditions for this appliance are
stated on the rating plate which can be found on the back cover.
This appliance is not designed to be connected to a combustion
products evacuation device. Particular attention should be given
to the relevant requirements regarding ventilation.
Connection to the cooker should be made with an approved
appliance flexible connection to local rules. Models for use with
LPG should be fitted with a hose suitable for LPG and capable of
withstanding 50mbar pressure. A length of 0.9 to 1.25m is
recommended. The length of hose chosen should be such that
when the cooker is in situ, the hose does not touch the floor.
The temperature rise of areas at the rear of the cooker that are
likely to come in contact with the flexible hose do not exceed 70
0
C.
Gas pressure may be checked on a semi-rapid hob burner. Remove
the appropriate injector and attach a test nipple. Light the other
burners and observe that the gas pressure complies with the gas
standards in force.
Certain types of cookers can be set for sypply both on the right
and lefthand side. In this case it is sufficient to reverse the position
of the cad nipple reducer. At the end make sure than there is no
leakage of gas.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pelgrim TBF945 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pelgrim TBF945 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info