458015
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
2
If several radiator controllers are to be controlled simultaneously
in one room:
Press the binding procedure button on all the radiator
controllers consecutively.
Activate binding procedure at the command centre (see
operating instructions of the command centre).
During binding procedure, the symbol is shown
continuously in the display of the radiator controller. The
following is displayed:
.
The radiator controller receives data from the command
centre. This process can take up to 4 minutes.
Failed binding procedure
The binding procedure has failed if the symbol extinguishes.
Take the following measures:
Remove the disturbing/shielding devices, e.g. wireless
headphones, cordless telephones, loudspeakers, garage door
openers.
Repeat the binding procedure.
If the symbol extinguishes during normal operation, possible
causes are discharged batteries at the command centre. You do
not have to repeat binding operation, if the communication is
reestablished. If you remove the batteries and insert them again,
the HR80 goes direct in sync mode.
The set temperature at the radiator controller is
automatically set to 20 °C.
FINISHING INSTALLATION OF RADIATOR CONTROLLER
1. Turn the retaining bracket
on the operating unit until
the tip points upwards.
The lock on the coupling
module opens.
2. Slide the operating unit
onto the coupling module.
3. Turn the retaining bracket
to the side.
The operating unit and coupling module are connected
firmly.The
symbol disappears from the display of the
HR 80. The radiator controller is now ready for operation.
To separate operating unit and coupling module proceed in reverse
order.
OPERATION
Every local change in the setpoint temperature remains valid until
a time program overwrites it automatically.
The set temperature is controlled by the command centre and
set there as well. For further information please refer to the
operating instructions of the command centre.
CHANGING SET TEMPERATURE WITH ADJUSTMENT DIAL
Turn the adjustment dial of the operating unit until the desired
set temperature (between 5 – 30 °C) is displayed.
The range for the set temperature (standard range: 5 – 30 °C) can
be restricted at the command centre.
In order to open or close the radiator valve completely:
Turn the adjustment dial until "OFF" (closed) or "ON" (opened)
is displayed. (If temperature limits are set, "ON"/"OFF" is not
displayed.)
INSERTING/CHANGING BATTERIES
If Batt appears in the display, both batteries must be replaced.
If the batteries are too weak, the radiator controller opens the
radiator valve completely.
If the batteries are replaced after the binding procedure has been
completed,
is displayed.
The radiator controller waits for data from the command
centre (see section "Activating binding procedure").
1. Open battery
compartment.
2. If necessary, remove
empty batteries.
3. Insert the new batteries
into the battery compart-
ment. Ensure that the
polarity is correct.
4. Close the battery
compartment.
Do not dispose of batteries with household trash. They must be
returned in accordance with the local statutory requirements.
Always replace both batteries.
Only use 1.5 V alkaline batteries of the type LR06.
EMERGENCY OPERATION WITH EMPTY BATTERIES
1. Separate operating unit
from coupling module.
2. Use the adjustment dial to
open (in the direction of the
plus sign) or close (in the
direction of the minus sign)
the heating valve manually.
DEF (DEFAULT SETTING) AND FULL OPERATING MODES
In order to change between the two operating modes, press the
binding procedure button (1, section "Activating binding pro-
cedure") until the respective operating mode is shown on the
display.
Def (default setting) operating mode
The HR 80 operates with the optimum valve lift that is required
for room temperature control.
Full operating mode
If the complete valve lift is to be used or if the valve does not
close completely, you have to set the HR 80 to the full
operating mode.
The battery lifetime is reduced in the full operating mode.
RESETTING THE HR 80 TO THE FACTORY SETTINGS
Separate operating unit from the valve lantern, see Section
"Finishing installation of radiator controller".
Remove the batteries.
Insert the batteries again while keeping the binding procedure
button (see section "Activating binding procedure") pressed.
Attach the operating unit to the valve lantern.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Honeywell-HR-80

Zoeken resetten

  • Als ik een tweede HR80 aanmeld blijkt de eerst ineens weer niet aangemeld ... Wat doe ik verkeerd?
    Gesteld op 16-7-2023 om 21:36

    Reageer op deze vraag Misbruik melden
  • Hallo,

    wij hebben al een periode van langer dan 1 jaar een verwarmingsysteem met 2 groepen van Honeywell.
    De thermostaatknoppen zijn HR80.
    En hier zit het probleem.

    De knoppen gaan niet altijd goed dicht waardoor de kachel dan warm blijft.
    Dit gebeurt steeds vaker. De batterijen zijn niet leeg. Een keer helemaal hoog en hierna weer laagdraaien wil vaak helpen. Hebben meer mensen deze problemen?

    Gesteld op 8-2-2013 om 00:10

    Reageer op deze vraag Misbruik melden
    • ik ben er ook niet tevreden mee ook een jaar ingebruik ik heb 5 kranen, er is altijd een bij die zomaar op 30 graden blijft, ik kan er ook niets mee!!! Geantwoord op 19-12-2013 om 20:16

      Waardeer dit antwoord Misbruik melden
    • Dat kan komen omdat de HR80 vanuit de fabriek de kraan niet volledig open en dicht draait. Dit is te verhelpen door de HR80 in 'full mode" te zetten. Druk het knopje aan de binnenkant enige seconden in totdat er DEF of FULL verschijnt. De HR80 moet in FULL gezet worden. Geantwoord op 6-7-2014 om 15:48

      Waardeer dit antwoord Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Honeywell HR 80 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Honeywell HR 80 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Honeywell HR 80

Honeywell HR 80 Installatiehandleiding - Nederlands - 44 pagina's

Honeywell HR 80 Gebruiksaanwijzing - Nederlands - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info