30164
8
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
6. Installation
Connect the servos, batteries and switch harness in accordance with fig 2. Carefully
check to ensure that all connectors are properly seated.
Turn the power switches “ON” and operate the transmitter. Observe the direction of
travel of the control surfaces to see if they correspond to the control stick movement.
Improper servo direction is corrected with the servo reverse switches (fig 3).
Operate each servo over its entire range and check for binding of the push rods. Correct
as necessary. Hold each control stick at its extreme position and listen for servo hum.
The hum indicates that the control linkage is too tight for the amount of servo travel.
This is corrected with the end point adjustment or by lengthening the push rods.
Applying unreasonable force to a servo output arm will adversely affect the servo and
quickly drain the flight batteries. Therefore, all control linkages should operate as
smoothly and as frictionless as possible. Use Hitec “Jam Check’r” to assure smooth, safe
control setups.
When installing the switch, cut a rectangular somewhat larger than the full stroke of the
switch, then install the switch so it moves smoothly from ON to OFF.
The length of the receiver antenna is critical to the reception ofsignals transmitted,
therefore DO NOT cut or bundle the antenna wire, make every effort to keep the
antenna wire fully extended. Keep receiver antenna away from power & servo wires.
Keep off the metal frames.
Protect the receiver from excessive vibration by wrapping it in sponge rubber (note: Use
Hitec “Flight Preserver: #58480”). Next place the receiver in a plastic bag. Secure the
plastic bag with rubber bands to keep out moisture and dust.
Collapse the transmitter antenna fully and operate the system from a distance of 60 to 90
feet. The system should function flawlessly. If it does not, check to see that the receiver
and transmitter batteries are at maximum capacity.
7. Charging Instruction
Before first use of the Focus system, connect appropriate charge connectors from
charger to transmitter and receiver switch harness with battery connected.
With transmitter and receiver switched OFF, plug charger into 110-120V AC and be
sure the RED & GREEN charge lights are ON. If either charger light is OFF,
recheck connections to charger and be sure switches on transmitter and receiver are OFF.
Charge for 24 hours first before further use of system. This conditions the batteries for
full-charge capacity.
Re-charge 16-20 hours immediatley before flying day.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitec FOCUS_6_FM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitec FOCUS_6_FM in de taal/talen: Engels als bijlage per email.

De handleiding is 0,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info